Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello,
I have tried to apply for the SUPL license twice now. I was denied the first time for unspecified reasons and it has been over two hours since I submitted my second...
When I program the nrf9160dk with the example, the code detects the SSD1306, but the display looks like:
The image is only using the middle half (16 rows) of the display...
Hello,
I am new to thread technology, and I would like your advice. I studied thread CLI example and thread client and server examples. However, in these examples I did...
Hi,
Is there any example or libraries available for BLE direction finding with nRF devices. Including libraries for Angle of Arrival/Angle of Departure calculations, antenna...
Hello, when I try to send data via the UART interface using a printf statement, unfortunately this does not really work. Only one byte is sent and after that the application...
hello,
I have downloaded the DTM firmware and connected it according to the serial port pins defined in the figure below,
The selection of GPIO pins are pin 18 for RX...
I am trying to use the nRF as an intermediary bootloader for another microcontroller. All that I need the nRF to do is accept a 64kB binary file from my computer (at the moment...
Hello,
I have been testing the " ble_app_multilink_central " example given with Nordic SDK * nRF5_SDK_16.0.0_98a08e2 *.
nRF52840_DK board is working as the multilink...
I am getting an error when trying to run nrfutil, any tips on how to fix this?
~ ᐅ pip3 install --user nrfutil Requirement already satisfied: nrfutil in ./.local/lib/python3...
Hi,
I am developing project using nrf52840 and currently developing using SDK 3.0. (Once I complete my feature I will update to SDK4.1).
I am using the light bulb firmware...
Hello I am trying to run a simple zephyr bluetooth sample using nrf Connect SDK v. 1.5.1 I am using your nRF5340 DK The sample I am running is: beacon I followed your instructions...
I have one TX and another RX codes for data communication by ESB protocol. To verify whether data whitening can be enabled, I added below register setting on TX side only...
Hi. I'm developing nRF52832.
I'm in the process of setting up BLE, but there's a problem.
There was a problem while I was organizing the files due to successful BLE communication...
Hi,
I can able to get the DEVADDR0 and DEVADDR1. I am not able to make out How this EUI64 id is calculated using the DEVADDDR value.
I always get F4CE36 starting numbers...
