Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
SDK: 4.1.0
CHIP: 52840
old question
my sleepy zed lost connection to the coordinator after refreshing key of the coordinator.
1) how can I manipulate refresh...
Hi All,
Is there any proper method for updating the firmware via serial port of nRF52840. The same process as arduino or esp32. Can we invoke the updation process with a...
Hi Nordic Team,
Summary: Please guide to open and build simple example nRF5340 project using Segger IDE on Windows 10
Details:
We tried to have Segger IDE setup for...
I am trying to compile a sample application for the Board nRF5240 . While i install the nRF Connect SDK for ncs v1.5.0 through Toolchain Manager 0.9.1 , I get the error as...
HI,
Is it in anyway possible to change the maximum gazelle payload size to 64byte instead of 32byte, I need more data when I send data return to the device.
Hi.
I am working on the MSC, and starting with the usbd_msc demo. The windows explorer will show a disk named "USB Drive" if connect to the PC.
I would like to change...
Hi,
I am using SPIM in nrf5340 to read datas from 2 sensors. The sample rate is 400Hz, and I have to send and receive 8 bytes to each sensor every 2.5ms.
So I set up one...
Hello,
I want to judge the end of a file. In the past, I can directly call the feof() function when writing in C. Now I call the api in "fs.c & fs.h" in the example of zephyr...
Hi,
On a nRF52840 based coordinator, I want to support Zigbee 3.0 install codes and legacy devices with HA predefined link key at the same time.
1. Is that possible by...
I am working on a device driver for the W25Q128JV flash device. This is the first SPI device I've used with the nRF52840. I had some observations and questions about SPI programming...
Hi - I've bought two nRF5340 DK kits for some development work - and after about a week's effort and searching Nordic Semi documentation, Youtube and the internet in general...
I develop my own device on nRF52840 which will be HID device. And I have made my own HID descriptor of device:
And if I send data with function from example:
...
Hi,
As an alternative to writing a configration software for my device (a native app for windows or maybe android) I,m considering putting physical controls on the device...
I've installed Zephyr RTOS and built blinky example for NRF5340-DK board. Then, when I tried to flash output hex file into NRF5340, nrfjprog (using "west flash" command) gave...
