When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
How can configure NRF_LOG_UART to use UART0 or UART1 for nRF52840? I cant see any configuration which uart NRF_LOG_BACKEND_UART will use
As per spec nRF52840 should have...
Hello,
I want to develop a new IOT product using the NRF52840. My device will be using the MCU with BLE and a very low power sensor.
I want to use a 3.7V one cell battery...
Hi,
I would like to input a data(integer) into the CLI and store the data. How can I do that. I have seen SDK but could not find any function or macro.
If there is any...
Hello, Not sure if this is exactly the same as what is happening in this case , but the issue of an early disconnect when NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 247, can simply be...
Hello
I would like to retrieve the signal strength of the Thread messages I receive. To do this, I used the otMessageGetRss (message) command in my request_handler but the...
I have cloned a few beacons with nRF Connect and use the app to advertise these when testing our beacons and apps. It is (to my best knowledge) not possible however, to export...
I have been trying to use the secure services to read random from the CC310 and have been getting unpredictable crashes. I have been able to modify the secure_services sample...
sdk ncs v1.3.
Example name: serial_lte_modem. Example path: D:\ncs\v1.3.0\nrf\applications\serial_lte_modem
The error in opening this sample macro definition is as follows...
Hello, Nordic developers. The ZED , ZR and ZC connections were identified by the example of Zigbee Light Control example .
Based on this example, we are going to develop...
I am using the gazell protocol of nrf52840, How can I specify the correspondence address of this different handles when I USE A HOST to communicate with eight handle devices...
Hi,
I have looked at the different post regarding the nRF9160 and SPI, but I can not get it to work on our custom board.
Attached the board definition files.
Here...
I have the Thingy91 plugged into a macbook pro(osx catalina) with usb.
I have updated the firmware on thingy 91 with the precompiled application and modem firmware ( 2020...
We are able to form a openthread mesh using CLI-ftd examples.At present we have server communicating to Clint in UDP portal .Is there is any UART command which is meant for...
Hello.
I am using SDK v17.0.1, nrf52833.
I can enter DFU Mode with pressing Button 4 and reset Button.
However, I want to enter DFU mode without any Button.
I've...
