Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I'm using NRF52840 device to connect to a mobile via BLE.
Sometimes, I have error 133 and disconnection.
Can I initialize my BLE in a different way (characteristics...
int main(void) { bool erase_bonds; ret_code_t err_code;
log_init();
{ // Initialize the async SVCI interface to bootloader before any interrupts are enabled. err_code...
Hi,
I am using nrf mesh 5.0 sdk and nrf 17.02 sdk for nrf5832 board and want to implement scene setup server model in the light ctl and light lc model combined. I am not...
Hi,
We are working on our new product which needs a BLE connection with a mobile phone.
Our requirements are as follow:
1) Four digital output. (It's preferred to be...
Hello,
From the ble_app_uart example I created a version where instead of the UART the incoming data over BLE is processed using the scheduler.
Processing is not much...
Hi, i develop a bluetooth project with nrf52832 anad i am unexperinced about this topic. I searched for 2.4 GHZ antenna desgin bu can't found. There is a few topics about...
HW: nrf52833-DK
SW: SDK v16.0.0 and SoftDevice s140
We are using nRF52833 BLE direction feature and read IQ samples produced by BLE Radio.
The format of the IQ samples...
I am working on porting a project from the old sdk to the nrf5340 and the nrf connect sdk documentation seems to be incorrect and i am having major issues even getting this...
SoC: nRF52810
SDK: 17
Hello,
I want to confirm whether BLE_DFU_ENABLED is used or not.
InfoCenter ( https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/group__ble__dfu__config...
Hi,
I use the app "asset-tracker", and i would like to configure an external uart to connect a sensor to the board.
I modifed the code but i can't detect any new COM from...
Hi,
I am using nrf51422 and s130 softdevice for multirole. Is there any way to reduce the receiver power during scanning so that the overall current gets reduced?
Hi,
I'm trying to implement remote provisioning on an altered version of the light switch example in the SDK for Mesh v3.2, on nRF52832 development kits. The code I'm using...
I am using nrf52832, i want to send the sensor data continuously via ibeacon.
but while uisng sd_ble_gap_adv_set_configure() function return error NRF_ERROR_INVALID_STATE...
