hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I am trying to understand the following, hopefully someone can explain:
AFAIK, BLE advertising is stopped as soon as the limit of the SD is reached, AKA the PERIPHERAL_LINK_COUNT...
Hello, I am I'm a novice at developing NRF 51822. My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
It's being developed in this environment. Q1 .NRF...
Hi. I am struggling to build the DFU secure bootloader example for the n52 DK development kit. Using SEGGER embedded studio.
I get the following error;
cannot find .....
Hi Support Team,
We bought the nRF52 DK along with the PPK so we can measure current consumption of a DUT. It was working on the power profiler App in nRF Connect and we...
I am starting up with nRF52840, currently i have the dongle but expected to receive my DK in the next few days. This is my first BLE project, so i started reading a lot of...
We have a BLE peripheral implementation using the nRF52832 and both the S332 v2.0.0 and v7.0.1 softdevice. We are supplying the LF clock to the nRF52 from an STM32 MCO output...
Hi,
I would like to set up a couple of boards communicating over Bluetooth; I was hoping someone could provide some pointers.
I would like to connect the nRF9160DK to...
Hello, i'm trying to get usbd_msc example to work on custom, test pcb, with Microchip SST26VF064B flash chip (SDK version 16). As previously advised, i have redefined NRFX_QSPI_PIN_xxx...
Hi,
I wanted to setup a dynamic buffer but I don't have any leads on how to set it up.
Basically, i want to store a stream of data every time it is recorded and then send...
I know this has been asked a couple of times, but I haven't been able to find a straight forward answer.
I have a GPS module that spits out data via UART (no flow control...
Hello, Team.
I always thank to you.
I tried to find some information, but it is a little bit hard to find, so I upload this Q&A.
Now I'm interested in Mesh protocol...
I would like to store unit configuration information into the UICR "customer" area. This is done only once, on first startup, saving configuration received from the host....
Hello all,
I am developing a custom application on a Ruuvi tag with nrf52830 ic. I am using the latest sdk17 and softdevice s132 7.0.1. I am having problems updating the...
