hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I am trying to use as least energy as possible. I run the ble_app_blinky example. The only change I did was commenting out: advertising_start(); such that no advertising...
Hello,
I'm using the nRF52840 Development Kit and SDK16.0.0_98a08e2.
I'm trying to run the example "proprietary_rf\esb_ptx\pca10056\".
It compiles and runs if I do not...
Hi,
I am not getting the exact starting and ending address of user flash storage like other controllers, How we can find that while using FDS and Fstorage and also i want...
I have a custom board with 5 buttons, and a status LED, using the nrf52832_xxaa chip. 2 of the 5 buttons never trigger an interrupt. It seems like this is because nrf_gpio_pin_read...
Hello, Nordic.
I'm currently developing multiple sensor beacons and a scanner for asset tracking (scanner app based on ble_app_uart_c)
ble_app_uart_c has SCAN...
Hello,
Im designing a board with nRF52832 with acceleration sensor and BLE application, so for the esd protection, should there be an housing of some sort, what all can...
We're migrating from Zentri AMS002 chip to to nRF52840.
We use custom service UUID: "175f8f23-a570-49bd-9627-815a6a27de2a" in nRF firmware.
As attached images show, custom...
Hi!
We're developing a board where we would like to switch between normal power mode (VDD shorted with VDDH) and high power mode (VDDH as input and VDD in highZ or supplying...
Hello everyone. I'm looking for BT5.1 most supported at current moment chip - to have devboard and SDK with ability of direction finding. Which one you can recommend? As I...
We are working with nRF52, in that we want to select any fix channel of BLE. We does not want to use ADH mechanism due to form a whole network on one channel.
So can you...
this is the log I'm getting but it is not clear for me why is the build failing
Building ?spm/zephyr/include/generated/driver-validation.h? from solution ?build? in configuration...
I need to add new files to the aws fota example for the nrf9160 project in order to implement compatibility with the
AWS OTA update agent, I have read other posts in the...
Hello,
I've been starting to get into level 0.1 programming after being able to loosely control an LED with GPIOTE and a timer interrupt using examples and API references...