Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I'm attempting to write a plugin/dll to pull data from the Nordic Thingy52. I can scan all devices that are paired with windows 10, and load up the services, etc.
I can...
Hi,
I am trying to replicate the benchmark numbers stated by Nordic for the nRF52840 to verify I have setup the chip correctly for maximum performance. I have caching turned...
Hi everyone,
I try to send my nRF52 DK board to an android application.
nRF52 example source is "ble_app_blinky_pca10040_s132" and Android app sample is nRF-Blinky from...
Hello everyone,
I am trying to develop a windows application using the same example from pc-ble-driver-4.1.1\examples\heart_rate_collector/main.c. When i call the function...
I am currently working on a project where I try to send data from a swimmer in the open sea to a point on the land (beach). I know that Bluetooth communications are blocked...
Hi,
I am advertising with device name A but if someone holds a mobile to the NFC I would like to switch to NFC OOB pairing but with a different device name B (SDK version...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have gone through wdt...
Using the samples/nrf9160/at_client sample application, the AT command AT+CLAC crashes the modem or AT host firmware: it no longer responds to any AT commands.
Details:...
What are the best practices when processing BLE GAP scan events to avoid multi-threading issues?
I programmed the nrf52832 to successfully read BLE GAP events coming from...
I'm having trouble getting the Bluetooth Low Energy desktop library ( https://github.com/NordicSemiconductor/pc-ble-driver/tree/v4.1.1 ) set up on my Mac. My problem is occurring...
I would like to know what is the maximum ADC sampling frequency for transmitting data over Bluetooth to PC.
I am using two modules having an nRF52832 for each module....
Hello, I think there is an error in ble_advertising.c (SDK 15+).
Line 608, the code is trying to set the secondary phy but checks if the primary phy is valid ( ble_adv_primary_phy...
Hello,
I am very new to evaluating the nrf52-dk board, so I hope this is not too much of a trivial question.
I was trying to enable logging via UART without having to...
