Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
This is a really weird problem.
======================
Setup of 52832 hardware:
- Custom board, using 32MHz XTAL and LF RC.
- SDK15.2, S132 610
- Segger RTT...
I need a 30 second hardware based interrupt for a Nordic BLE nrf52832 chip running S132 Softdevice. I would like to use RTC2. This will be used to run a short BLE ad scan...
Hi, for a project at my university I need to analyze BLE signales. In this context I need to demodulate a BLE signal AND extract the I/Q samples from the same signal. Does...
Hi, I have my nrf51 Dk (PCA10028) on which I want to connect a buzzer or speaker to one of the gpio pins which are not in use. I am confused on the following points:
1....
I'd like to know if it’s still true that the DFU bootloader (i.e with BLE transport) is strongly coupled to the SoftDevice version. In other words, if we do a SoftDevice over...
From page 520 of nRF52840 Product Specification 1.0 4413_417 v1.0 / 2018-03-16
If the watchdog is configured to generate an interrupt on the TIMEOUT event, the watchdog...
I am trying to flash all three images together. I have the firmware updating working, but if you flash them together, the bootloader doesn't know that the application is programmed...
Hi,
We are preparing the first "production" run and we are looking on alternatives for production programming and testing, so far our factory used nRFgo for the pre-series...
I need to have more than 30 servers (and 1 client) in a mesh, so I increased the SERVER_NODE_COUNT value. But this results in a static assert in config_server.c:
How to...
Hi,
I know that this issue is well documented in the forum, but I have read everything and tried all of the suggested fixes, but nothing worked.
I am trying to Enter systemOFF...
Hi,
I have tried to find out how to aks the current time and set it, without success.
time(NULL) returns invalid data. What methods I should use to get the current time...
I want to simply put signal (sine wave) from signal generator into analog input and use saadc. I have program which uses ain4 and ain5 pins. So I was just wondering how I...
Basically I have modified the ble_app_uart example to connect multiple centrals(android devices),
now i want to transfer the string to all android devices which are connected...
Hello,
Would like to know the performance(i.e, latency when network size increases with respect to payload) of Thread, Zigbee, BT mesh wireless protocols. Is there any documentation...
