Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Issue with Zephyr software platform and sleep state for the Nordic chipset. We can see when using the power management sample code for Zephyr that it consume 300 uA in sleep...
hi,...... i am merging the nRF52832 and heart rate sensor BH1790, SEGGER 15.2V i want to read the heart rate sensor , for that i want to write the paramater of address, 41h...
After beating my head against the toolchain for quite a while, I finally managed to get SES to compile the ble_app_uart for the nRF51822 using the s130 soft device. It works...
nRF52832(PCA10040) plays role of central(ble_app_multilink_central) and
HM-10(TI 254x) runs as spp peripheral.
nRF52(with SDK15) receive adertizement packet but loss...
We are using device nrf52840 with sdk 15.0.0
The problem is: High current consumption, typically around 2 mA. But over time drifts up to 9 mA in a period of 12 hrs.
...
Hi, first post here...
I've been using Nordic in the form of Laird modules and SmartBasic to get my application up & running. Now I want to migrate to using the nRF devices...
Hello,
I am trying to use nrf-mpu-examples in eclipse from this link github.com/.../nrf5-mpu-examples . I have provided all required libraries and header files but I am...
I am developing a device that will receive over the network lte a video signal in real time and display it on a screen with a resolution of 13-15 inches. Based on the chip...
I´m trying to build an application similar to the peripheral side of the app_mtu_throughput example. I need to send a large buffer via notifications to the server.
I'm using...
I am using NRF-52832 on a custom hardware. It works well on Android but on IOS (e.g. iPhone 7) it disconnects after 30 seconds.
After analysing with the sniffer, its observed...
Hi,
I had change NRF_ESB_MAX_PAYLOAD_LENGTH to 250 and modify payload_length of NRF_ESB_DEFAULT_CONFIG to 250.
Why I can only send 8 byte packet out by using "nrf_esb_write_payload...
log.zip
I use custom board for nRF52832
I connected it with JLink, and installed SD132 with nRFgo Studio (successfully)
after then, I cannot connect to chip
...
hi guy . I m triyng to understand if could be possible to send a at least 300 hz input signal beetwen two boards nrf52840 with the trasmission protocol ANT.
I tried to use...
Hi!
1. We are using 1 Client over Serial and 30+ Server nodes over mesh network
When you want to know FW info regarding Client, you can call serial command like Opcode...
Hi, I'm working on project using nRF52840-DK board with nRF5_SDK_15.2.0_9412b96. The program collects data from two UARTs, process data and sends results to Android over BLE...
