Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I want to get vdd without timer
so i found this.
https://devzone.nordicsemi.com/f/nordic-q-a/38239/nrf-52832-saadc-without-timer/147517#147517
and change some part like...
I have a design, using the NRF24L01+, that I would like to run from batteries. The Transmitting device is not a problem, because it can turn off when not transmitting.
For...
Hi All,
For NRF52 is that possible to configure the system to use a different pin for RESET than GPIO 21? We want to reset the NRF on errors, if our other MCU detects some...
Board：PCA10056 （0.9.3）
SDK：15.2
Softdevice：S140
Example：ble_app_blinky
Today，I follow this page Using an ampere-meter for current measurement to measure the current...
Used SDK: 15.2.0
Hello,
I want to print some debug messages over RTT after an error occured. After that I want to reset the system.
If I put the string into the que...
I've followed the steps to set up the SDK.
When I execute the batch file(setup_sdk.bat), there is something wrong occur (as below pic)
I've installed the git and add...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi there,
I am trying to use UART on the nRF52840 on a custom PCB. The custom board is connected to the nRF52840-DK with a debug connector. Am I free to set any pins on...
I want to create a router that only communicates with Bluetooth, not the gateway that connects to other networks.
The configuration is as follows.
C oordinator + Router...
Greetings,
I'm having troubles getting the Mesh lighting demo to work. Here are the details:
IDE = SES 4.12
SDK = nRF5 SDK v15.2.0, nRF5 Mesh SDK v3.1.0
SoftDevice...
Hi, Is there a usb hidapi sample code for nrf52840 somewhere? I know that there is a sample code of usbd_cdc_acm. Using the HIDAPI library link below , It will be beneficial...
Hi,
I am working on a Bluetooth Mesh project in which I am trying to add support for NFC, but I get the following error " error: multiple definition of `SWI2_EGU2_IRQHandler...
I'm new to nRF9160. I have some experience of implementing stm32 MCU and HL8548(3G module).
I want to send at commands to outside module like Wifi module, and receive return...
I have Nordic NRF 52840 DK development board, using Ubuntu 18.04, I loaded "ble_connectivity_s140_usb_hci_pca10056" to the board successfully. Then I powered cycle and cannot...
My setup: Eclipse, nrf52832 on a custom target board, s132, SDK13
I am trying to implement the workaround for the problem described here:
https://devzone.nordicsemi.com...
