Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi!
I am trying to use the NFC " writable_ndef_msg " code along with the " ble_app_uart " code from SDK 15.0 with Softdevice s140 on nRF52840 DK. I am using keil-MDK 5...
How can I be 100% sure the nRF52832 chip is running properly?, what I do to power up the chip is feed it with a regulated voltage of 3.3V (which really is around 3.17V), on...
We use Nrf_studio to connect our board by uart to enter direct test mode.
But an error occurs in serial connection.
I want to know， use our own project program is allowed...
I have already pressed reset in the dongle, it was pulsing red. And when I write it allways says the same error. I have done this experiment in Ubuntu 16.04 and Windows 10...
Dear all,
I'm struggling writing 32 bytes with FDS in SDK 14.
This is what I do:
Init
(void) fds_register(fds_evt_handler);
fds_init();
while(!is_init) {
sd_app_evt_wait...
Hi, I am using nrf51822 Development kit with 3 buttons, each buttons has different functions. (i) 1st Button is used for the wake the module from sleep mode. (ii) 2nd Button...
Hi I using nrf51DK using keil MDK 5 softdevice s110.
I need to update battery level on every 60s and I have initialize timer and start with this code.
static void battery_level_meas_timeout_handler...
I'm trying to implement extended advertising, using BLE_GAP_PHY_2MBPS to offload 255byte advertisement payload to channel data, defining BLE_GAP_PHY_1MBPS as primary phy ;...
Hi
I am trying to broadcast manufacturer data (beacon example) while changing data from second to second. For that I am trying to use timer2 (as timer 0 is used by SD, right...
Greetings,
For Bluetooth Declarations, will new QDIDs be generated to account for the additional required tests as of January 24, 2019 in TCRL-2018-1.
I'm mainly interested...
Hi,
I need to interface LIS2DH through SPI. I tried many SPI Master example but I am getting all the values as 0XFF. Even the WHO_AM_I registers value is getting 0xFF
...
Hi, I have an EMG muscle sensor which needs to be sampled at least 500Hz. Can I sample at the required frequency and transmit at the same time over BLE NRF51822. If not please...
Hi, I am new to the bluetooth mesh concept but I have tried creating one using nRF52 DKs.I have worked the light switch example but I am stuck there without being able to...
Hi everyone,
I bought the nRF51822-04AT module but I'm a newbie and all the documents talk about nRF development kits which they make me confused about programming. Now...
