Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
So I am brand new at this product line, and basically new at C in general, I come from VB land. So bare with me please
I purchased both a Nordic nrf52 dev kit evaluation...
Hello there,
I'm sending IMU data (16bytes) using a notification from a custom board to a phone. My final goal is to send this packet of data (16 bytes) every 10 milliseconds...
I am developing a mobile application with bluetooth mesh.
But i can not describe the structure of a node with demo application. The sequence that I want to understand is...
Dear Nordic,
I implemented a RTC calender in nRF52832 using RTC2 . I want to port this RTC calender to nRF52810 but 810 has 2 RTC.
RTC0 is used by softdevice and RTC1...
After getting the latest nRF9160 in (DK V0.7.0) I installed pynrfjprog, and then issued the following command (as provided in the README)
nrf9160_mdm_dfu --update
...
Hi, I am new to BLE mesh. As I have understand , a provisioner is one which forms the mesh network and assigns addresses to the node and make them join to the network.
1...
Hi,
How do I-
1. Start a timer when sending data from nrf to host (PC) in form of input report.
2. When the application running on host machine receives this data, send...
When i try to add RSSI viewer app in nrf connect it shows error
Unable to install: Unable to download developer.nordicsemi.com/.../pc-nrfconnect-rssi: net::ERR_CONNECTION_RESET...
I am experiencing strange behavior on the PCA10056. I have two boards now in the same state, both were working fine before starting work on the Secure DFU (uart). The following...
I found that App timer using in ble_app_template in different modules. Is it possible to change prescaler value without harm to other modules? I need to increase maximum value...
Respected nordic community,
I am working on one project where right now i try to make custom service read operation through nrf52832 in segger studio. From my device(mobile...
HI, I am seungwoo
I am developing data transmission using nrf52810.
A 300-kilobyte file is divided into 220 bytes and transmitted continuously.
11-27 17:24:24.416...
Hi,
I'm developing a unit which i need from time to time to send a packet throw I/O lines (F.E.virtual uart)
However the packet bit timing is very critical.
As far as...
Hi, I am using nrf52832 with SDK 12.3.0 and nrf 52 dev board. I am experiencing a problem whenever I programmed nrf 52832 using nrf52 dev board and NRFGO, after certain number...
