I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
I am in the startup phase of a uni-project and I would like to ask you about the feasibility of using the nrf24L01p with power amplifier as the radio module. Specifications...
Dear all, I'm trying compile github ble example ble_app_hello_world for Nordic nRF51422 following steps on Tutorial Advertising for Beginners and found 6 errors all same type...
Hello,
I am using enhanced shock burst as communication protocol. Currently i am using rtc 300us timer to call nrf_esb_add_packet_to_tx_fifo() to transmit data every 300...
I have a custom board with the nRF51822 chip, the chip is set-up with the recommended (CFAC WLCSP schematic with low voltage mode) setup, excluding the external low frequency...
Hi,
I just finish designing my board and soldering it using the Bluetooth low energy nRF51822 chip and i want to test it.
i want to know if i put the coin cell 3v and...
Is the ECDH encrypted key exchange supported on the new S130? If not, when can we expect it to be available?
I am surprised this is not given a higher priority, since now...
I use s110 v7.1.0 ,nrf51822qfaa.
now I find the pstorage_store work is OK if I is not run sd_ble_gap_adv_start function.
but I fin the pstorage_store work is wrong if...
I use s110 v7.1.0, nrf51822qfaa.
The write flash data using pstorage is OK ,before ble_advertising_start() function is start run.
But if I run the ble_advertising_start...
Hello,
I am using the nrf52pdk and am wondering if there is a way to force an output compare interrupt to occur. For example, lets say you want to generate an interrupt...
Hi,
on the nrfprog you can detect all connected Segger programmers.
If I have 10 Segger Programmers connected, I can address each of them with the nrfprog to programm...
Hi,
I am new to Nordic. Will someone help me figure out what is wrong with UVision V5.16a. I get sample codes from pack installer example the "ble_app_hrs_s310_pca10028...
I've followed the instructions here to try and get my J-Link debugger to run in bootloader.
I am using a newer SDK and SD (than the post was written for) so that may have...
Hi !
I have a rather strange problem: 1 packet is transmitted for 30 milliseconds.
I use iPhone-4s with iOS8.1 and custom board with nRF51822
In the firmware exists 4...
I saw that DA14680 from Dialog comes with a 30uA/MHz processor.
Although the clock can be programmed up to 96MHz, the 30uA/MHz is measures at 16MHz.
How can I get a...
Can you please clarify what the RBC_MESH_EVENT_TYPE_CONFLICTING_VAL is used for with the RBC mesh? I receive these events on the node that sets a value, but not the remote...
