Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I have achieved bluetooth direction finding using nRF52833DK. I would like to do the same with a custom board. I have used the BM833 chip for doing this. I have attached the...
Dear Nordic,
We made an attempt to use the external flash in the LwM2M sample.
We tried to follow this: docs.nordicsemi.com/.../nrf9160_external_flash.html
As soon as...
Hi.
When working with certain nRF connect SDK versions 2.x.x (not sure which range) in visual studio code, the build terminal outputs relative file paths when showing warnings...
I am looking for some simple slave and master samples to run on my dk's nut cant find any. in the intermediate course there is the master slave talking with the sensor but...
When will the nRF9151 Hardware Design Guidelines document be available?
We are currently leveraging information in the nRF9161 Hardware Design Guidelines document in the...
I am building a nrf52840 custom board and testing the ble_app_blink_pca10056_s140 example from segger I have a 32MHz crystal and a 32.768khz crystal And I added the following...
I've got a custom board using an nRF52832. I'm using the P0.06/P0.08 as the TX/RX pins for UART comms, but don't need the P0.05/P0.07 pins for CTS/RTS. Is there anyway I can...
Hello. I am currently working on a Mesh Network using the Nordic Thingy53 board. As far as I understand, the Mesh protocol developed by Nordic already has encryption, obfuscation...
Hello,
In a project using the NRF52832. Softdevice SDK 19.1.0 and Segger IDE, I inizialize the BLE for having NUS and DFU services actives. I try to reproduce the code here...
Hi,
I would like to ask when using zephyr's k_timer it uses a clock from LFCLK, then it can be generated in the following three ways:
32.768 kHz RC oscillator (LFRC) 32...
Hello Team NordicSemi Q&A,
I am beginer in Nordic Semiconductor Device. My question is related of nPM1300 Quiescent Current. In datasheet for Sleep Mode and Hibernate Mode...
Hi. i am trying to turn ON a LED1 and read its status and then turn ON LED2 based on status of LED1 in nrf52840dk board.
#define led1 28 #define led2 25 #define Button 12...
These seems like another dumb question. First off, I am aware that the nrf21540DK is the nrf52840 with the FEM tacked on the output.
I know I can select the nrf21530DK/nrf52840...
Hi,
I’m experimenting with the nrf9160 LTE modem in poor network conditions. I would like to be able to keep track of how long the modem spends searching for LTE networks...
Hello,
I'm having an issue with performing fw update with ble mesh DFU examples.
My setup is pca10056 used as distributor and pca10059 - dongle as target.
I'm using...
