Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi
1.
A. nRF7002 DK(NRF5340+NRF7002)
B. Our PCBA(NRF5340+NRF7002)
We found same application code flash to both. Sample A can work. Sample B can't work and stuck
...
Hi,
I was previously working with W25Q32JVSSIQ, a 32MBit memory device communicating with nrf5340 chip. The QSPI driver was initialized using NRFX_QSPI_DEFAULT_CONFIG()...
Hi,
I’m working with an NRF5340 device paired with a Nordic HID mouse. Currently, data encryption is enabled after pairing, but the encryption and decryption modules are...
Hi,
I want to know if Android Smartphone can be configured as BLE Mesh node? If it can be configured as BLE mesh node, how can it be done using below mentioned library...
Hi.
I would like to set the TX power level for broadcast streams to a higher level then the other radio packets (especially the packets on the primary ADV channels). First...
Hi,
I'm working with nRF5340 Audio DKs.
I'm able to successfully run the audio example in BIS mode (with gateway and headset devices).
My goal is to open another BT...
Hello,
I am developing a PCB with nRF52805. The PCB is small and must be cost-optimized. It also needs to be as small as possible.
For prototypes, I have added a J-TAG...
I was building the "console" sample code found in zephyr for my custom nrf52840 board and I managed to get it to work. But as soon as cryptocell gets enabled, it doesn't work...
Hello,
I need to run nrfutil on a raspberry pi3. The NRFutil executable I use on windows & linux found at https://www.nordicsemi.com/Products/Development-tools/nRF-Util...
I have new nrf9161dk that I'm trying to run the "quick start" guide for. However, when I get to the "Progam" step it fails. This is the error log: 2024-10-03T18:05:08.932Z...
Trying to put nRF52840 in OFF mode and I see the following odd behavior: If I put all the output GPIOs into Hi-Z mode, power consumption measured in-line with the battery...
Hello,
Do the micro controllers out of the box before installing onto a PCB already have a bootloader? What do I need to consider to be able to reprogram my MCU on the PCB...
I'm working with the nrf9160 dk and trying to get a baseline low power project before I add peripherals and application code. I'm using ncs 2.7, and with an empty project...
The idle power consumption (i.e. the current draw between adverts) is 2.4uA prior to the first call of dm_request_add() following reset.
Once a distance measurement has...
Hi, I am actually newbie to embedded system.
My question is how can I upload my code to MCU.
There are very good tutorial about developing with development kit.
So...
