Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
We would like to program the external flash connected to the nRF5340 via SWD during manufacturing.
Is this possible? Do you have any documentation that explains...
Hi
When doing a Software reset the RAM contents are persisted, however when doing a Hardware reset via nREST pin on the module then the non-initialized RAM section is...
Hi,
I am designing the ARGO module http://wizcube.eu/argo.html . I am using the excellent KiCAD library https://github.com/hlord2000/nordic-lib-kicad
It seems there is...
Hi, I'm developing a product for a client using nrf52840 which has support for DFU OTA over BLE. I'm using nrf connect sdk 2.5.0 and DFU OTA over BLE was ridiculously easy...
We're using a nRF5340 module on our board, and have basically everything working as we'd like using SDK 2.1.0.
I've tried updating to SDK 2.6.1, and managed to resolve all...
Hi,
In our new project, we are using the nRF5340 WLCSP package and configuring the system ON - low-power mode in our application code. We measured the current consumption...
Hi,
Ubuntu 20.3
vscode + nrf connect extension
when i create new application from exsample project broadcast_audio_source for nrf5340, after build, and flash into the...
Product: NRF9160
SDK: 2.6.1
Modem: 1.3.6 My problem is that FOTA download is breaking up more or less every time our device is doing a SW upgrade. We download SW directly...
NCS version : v2.6.1
target board: nrf5340dk_nrf5340_cpuapp_ns
sample project: "ncs\v2.6.1\zephyr\samples\application_development\sysbuild\with_mcuboot"
I use this command...
app and dfu works after I program the merged hex from bootloader_setting, bootloader, softdevice, app using Program application tab, but if I erase chip, reprogram it with...
Hello,
Because i want to connect more than two headset to one gateway, so i modify the prj.conf as follow
CONFIG_AUDIO_DEV =2
CONFIG_BT_MAX_CONN =4
CONFIG_BT_MAX_PAIRED...
Hey all,
Quick question. If we want to send BLE advertisements, beacons, for just 1-2 seconds, then shutdown into SYSTEM_OFF mode, could we initialize the BLE soft device...
I using XIAO nrf52840. https://wiki.seeedstudio.com/XIAO_BLE/
I am developing a BLE peripheral device using the nRF52840. This device is designed to connect with a specific...
Hi,
Could you please advise, am designing a device using the nrf52dk-52832 in nrf sdk connect 2.5.1 and toolchain 2.5.2 that reads the previously adquired samples data from...
Hello,
We decided to use the 802540 battery for our application with the nPM1300. To get a good estimate of the state of charge (SOC), we did the very lengthy battery profiling...
