Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I have been successfully using the Peripheral UART example on a 5340DK board. I tried rebuilding for the 7002DK, and am getting runtime errors. The UART initializes, but the...
Hi all, I am trying to understand the different Access Port Protection mechanisms on the nRF52840. From several tickets, own experiments and from the data sheet I was able...
Code runs fine in v2.53 but when running in v2.6, we get a kernel panic at the exit of a delayable workqueue function.
Tracing the code and line number, it dies in Zephyr...
I made a device based on the nRF52832 and am developing an app to control it. The control works great, I can send and receive BLE signals with react-native-ble-manager. I...
Hello,
I am working on creating a custom board using BLE BE33 module based on the nrf5340dk_nrf5340 board.
Previously i tried the peripheral uart and central uart to transfer...
The drivers in the paths
/opt/nordic/ncs/v2.6.1/nrf/drivers/sensor
and
/opt/nordic/ncs/v2.6.1/zephyr/drivers/sensor
are different.
I'm using NRF52 and VSCode with...
With nRF as advertising peripheral, is it possible to measure RSSI of active scanners' SCAN_REQ packets. `bt_le_ext_adv_cb` has a `scanned` callback, but it looks like it...
Hello,
I try to implement little fs to my external flash memory. I am using nrf52832 board and my memory is IS25LP128.
Without the connection of the memory the nrf board...
I wanted to change the Peripheral UART program in the nrf samples to the host_only version, and I made some attempts. I added the following code to the prj.conf file:
...
I am trying to get hello world to work:
/*
* Copyright (c) 2012-2014 Wind River Systems, Inc.
*
* SPDX-License-Identifier: Apache-2.0
*/
#include <stdio.h...
Hi,
Im just starting to use the nRF9160 with the SLM application flashed. All the samples and articles I found were always using stuff like the LTE link control library...
Hello,
when I play around with the matter template example, I always get a thread child device. How to get a full thread device with routing etc?
Thanks, Edi
Hi,
I'm using a Azure IoT Hub to connect some devices to the cloud and then uses the Direct Method to send messages to the devices. I can send messages and receive the response...
Hello,
I want to work on NRF52832 using VL53L3CX. When I look at the SDK, there are source files for VL53L0X and VL53L1X. I have previously worked on VL53L0X using this...
