Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi Team,
The customer have used NRF52832-CIAA-R. The datasheet of the Bluetooth module has NFC function. Please help provide the reports of EN 300 330-1 and EN62311 for...
Hello Nordic Forums.
I have been struggling for the past couple of days to try to get the SPI working. I never thought that something this easy could have become such a...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Hello,
I was wondering if there was a way to implement a physical on/off switch to the npm1300 that would allow the outputs to be isolated form the battery but still having...
We are checking the feasibility on LE Audio + Mesh + Bidirectional streams. A picture is attached for the situation. We would like to know how to apply Mesh network on LE...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if all of the power components are required.
The nPM1300 appears to provide...
Hello,
We have a requirement to ensure all private keys are stored within AWS Key Management System (KMS) and the only way to interact with these is via the KMS APIs that...
Hello,
The documentation in the nRF7002 Product Specification rev 1.0 says that the P2P mode (Peer-to-peer) is supported (section 6). However in this ticket: https://devzone...
I recently had a question about AES encryption on the nRF9160 and about how to store 32-byte encryption keys. The ticket was closed after I got the following answer: " we...
Hi,my board is nRF52840,and the demo is periodic_sync_conn within ncs2.7.0,
I want to establish periodic sync with the AP whose rssi is better，but i am failed。The ESL will...
Hello Nordic team,
I am working with the samples/bluetooth/shorter_conn_intervals sample on NCS v3.2.3 using two nRF54L15 DK boards.
I understand the difference between...
Hello, Recently I got an nRF9151-DK and I am following the Cellular IoT Fundamentals course. When it was time to connect the device to nRF Cloud (Lesson 1, Exercise 1), it...
Hi there,
I am developing a Matter light color temperature lamp product based on the NCS v3.1.1, and I need to store some custom user data in NVM (Non-Volatile Memory) within...
Hi engineers,
I posted a question at the link below, but it doesn’t seem to have received a response yet. If it’s convenient, could you please help answer the question?...
