Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
I am new to nRF MCU's and nRF connect SDK, I want to interface my INMP441 (I2S MIC) with my nRF52840 MCU to print the mic data on serial monitor , can anyone please link me...
Hello, I am working on a project for nRF9160 that is supposed to provide FOTA/DFU functionality for main application, modem and nRF52832 co-processor acting as SPI HCI slave...
Hi Nordic Team,
I am currently working on developing applications for custom boards using the nRF Connect SDK v2.6.0, specifically focusing on the nRF52840 microcontroller...
I have build a simple program to Interface my PDM (ICS 41351) Mic with my nRF52840 DK usnig nRF SDK on VS Code, although the program in build and flashed successfully I cant...
Hello Nordic Team!
I updated to version 5.0.0 of NRF Connect for Desktop and since then, when I try to program my development kit in VS Code, it can appear as connected...
Hello,
I wanted to evaluate the nRF53 platform with nrf connect SDK so I got new nRF7002DK board. I have following versions of all tools installed.
- nRF connect SDK ...
I want to edit the sample source (nRF5340 Audio) and program it on my own board. The connection is CIS. I am using NCS version 2.5.0.
I want to set the I2S clock as follows...
I tried the following settings to output 12.288MHz I2S MCLK with nRF5340 Audio, but it did not work as expected.
The I2S settings I want to output are as follows.
MCLK...
I am currently writing sniffer firmware to the nRF52840 and am trying to check Thread communication using WireShark.
When I displayed the RSS, I got the value shown in the...
Hi,
I am just starting to develop a nRF5340 based prototype. I am using the openthread CLI example as the first step. I have configured the device tree to suit our board...
Hello. We recently started working with the new nrf connect sdk and we need to implement a very simple bootloader that would only jump to the main application at a specific...
Hi there,
I have a project developed in SES, using nRF5 SDK v15.3.0 with only Just Works security without using LESC running on nRF52840. It has been running fine for 2...
In our custom board we checked WIFI, facing below issues, 1. We flashed sta sample project to our custom board facing the issue below. Is there any configuration needed to...
I am using Asynchronous API of uart to receive the data. During the reception I face UART_ERROR_FRAMING issue in UART_RX_STOP event. But after getting that too it enables...
