hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I'm interested in increasing the range I can get out of an Isochronous connection between two nrf52832 while maintaining about the same throughput. I'm not concerned...
Good morning,
In our next product (mounting a nRF52840) we will need a dual UART+BLE update channel. We have already implemented the update via BLE and we are now trying...
In SDK v2.6.1, commenting out the following code in websocket.c allows successful connection to the WebSocket. However, in SDK v2.7.0, even after commenting out the same code...
Hello! I have a Nordic nRF52840 BLE dongle, and I want to scan/sniff BLE air using custom BLE parameters: scan window and scan interval. How can I achieve this correctly?...
Hello,
I'm trying to figure out why GPIO 26 and 27 on the nrf9151 DK default to HIGH. I have my SALAE USB scope connected to several pins. When the board resets, only GPIO...
I am using an nRF52840 and nrf52832 to measure distance, but the reported value is almost twice the actual distance . For example, when the actual distance is 1 meter , the...
I would really like to use Bluefruit and make a Long Range connection between Servers and my Central. I know that it is not build in Bluefruit by default, but there must be...
Hello!
I'm using BLE Mesh sensor client receiving messages sent from multiple sensor servers. I used 2 nRF54l15DKs as 2 sensor servers, each sending 9 16-bit float data...
I have a problem with connecting to my device after i disconnect from it. I have tried ubond function, it does not work. This is my disconnect function:
I have a service...
Hello Nordic support,
My application is based on nRF5 SDK for Thread and Zigbee v4.2.0, with Softdevice S140 as I want my application to operate in either in BLE or Zigbee...
I'm trying to setup an SPI communication between an EVK of the Intan RHD2216 and the nRF 52840.
Browsing similar issues, I read the following topics already
I apparently...
I've been using the following SPI1M pins and they've been working:
But I have migrate away from these pins due to production PCB layout problems. The pins I need to...
I'm using nRF Connect SDK v2.7.0 with v2.7.0 toolchain to program a device with nRF52840 SoC.
When configuring task watchdog timer with hardware fallback an assertion fails...
Hello,
I'm exploring the possibilities of implementing the Nordic UART Service but am having trouble understanding its security functionalities. I have a few questions:...
