I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I am following the Dev Academy course for Cellular IoT Fundamentals with the Thingy:91. The Programmer software tool's "SelectDevice" tab does not detect any devices connected...
Hello,
I was wondering if there is a <complete> example someplace with Systemview running - an example for the nRF9160-DK would be nice.
I have the following in proj.conf...
We have a nRF52840 peripheral using the S140 SoftDevice on the SDK15.3.
Our peripheral is configured to advertise with the following advertising data: flags (BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE...
Hello
Sorry for the dumb question, but how do I get this timer to work?
What am I doing wrong?
I would like to measure the distance with the HC-SR04 sensor.
...
Hello!
I am having some GPS problems with the Asset tracker v2 firmware. It can find satellites, but it doesn't track them nor do I get a GPS fix before the timeout occurs...
Hello!
Our plan is to have the whole Bluetooth stack (softdevice controller, HCI, host) on the NET core and make APP core call the functions by RPC. The board is an nRF5340DK...
In my project, I need to set REGOUT0 to 4 , to achieve a VDD of 3 volts. In zephyr/boards/arm/nrf52840dongle_nrf52840/board.c there is an example showing how to do this in...
Hi,
I was about to program my nrf52840 with minor changes in the dts and after that I cannot flash any other images to the device. This is what I get when I flash the...
Hi~ I have a new NRF52833REV3 xxAA board, and I need to read its SRAM. However, when I use the JLink command to read it, I get 524288 bits 0. I have tried recover and erase...
Hello,
I am planning on using a 0201 15nH shielded inductor instead of the 0402-size listed on the schematic for the nRF52832.
Here's the link to the component: LMCI0201...
Hi Nordic,
We are now creating a BLE central device which can connect to an BLE peripheral device for some telemetry purpose.
To address privacy concern, the BLE peripheral...
Hello,
I have a workspace project that currently builds fine, however I am starting some new smaller projects and wish to build them as Freestanding so that I can have them...
Code snippet below produces the error code 0x00000001 during nrfx_spim_xfer:
The same SW in a different project does not produce the error. The error occurs during attempted...
Hello,
I have a project of a device with 2 endpoint plus the GP endpoint (242). It's a coordinator.
at first startup, the green power endpoint doesn't appear in the response...
Dear Nordic,
I'm trying to use the LTE Link Monitor and the Trace Collector V2 at the same time in order to collect trace messages from an nRF9160 DK. However, the RAW and...
