Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
On nRF5340, we are using Thread communication, Wifi and LTE-M module.
User can change the interface board, between Wifi or LTE-M module on the same UART bus.
& uart0...
I changed the central UART example to work with a demo I'm writing. I removed the hardware UART part and only send messages to a peripheral. What I do is I measure different...
I'm using an nRF52840 and SDKv17.1.
I have an active-high interrupt source connected to a GPIO pin. I understand that a GPIO should be able to wake up a system from system...
I think the nRF Connect toolchain is missing the right driver for the CLI app on the USB dongle, or the CLI is not setting up the USB interface with the right VIN.
When...
Hi,
Trying to run one of the Acconneer samples I get the errors below:
service_handle = acc_service_create(envelope_configuration); returns a NULL handle, all up to this...
I'm trying to connect my nrf52840 to the App but I have error message and impossible to continue ...
Here the log of the app standalone :
2022-10-07T21:50:58.341Z INFO...
During the software testing process, our device is connected to the rtt viewer for testing. At present, a problem is found during the test: sometimes the test engineer suddenly...
Can a single sdk_config file that has all possible macros definitions to use with an SDK
(1) be provided ?
(2) so that an identical sdk_config file be inserted in all...
Hello,
There is a missing #ifdef check on the following line of SDK Zephyr at the latest version v3.1.99-ncs1:
https://github.com/nrfconnect/sdk-zephyr/blob/98bc3a7a6b3917ce5a058e7a7271d3036edffb88...
I changed Kconfig of u-blox board template and something is going wrong in create_nordic_project.py when I tried to create project in Segger Embedded Studio from changed template...
hi support team,
there is one question feedback from customer, device（832）is sending data to mobile device, however this connection is disconnected （however there would...
Hello,
very early evaluation question, the 52832 has NFC-A. Is a mobile phone capable of reading from this device (some arbitrary user data) ? Now I've started looking into...
Dear,
- nRF connect SDK 1.9.1
- nRF5340 DK
We use 5340 spi to control an adc chip. The sample rate we need is 1kHz, so we use k_timer to produce a 1ms timer.
However...
