Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Since the previous topic was closed by accident and not able to reopen again, I will continue here.
Menon said:
Sorry I didn't get you well. You are using nRF5 SDK just...
Hello to all,
Below are the setup details I'm using:
nRF52840 DevKit
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Segger Embedded Studio 4.16
Aim: Controlling...
Hi ,
I have added simple on off mode in my previous application which was based on Generic ON OFF model. Code for simple on off model is added in both server and client...
Hello,
I have on nrf5340 an application, that meassures Temperature every second. I need to send the data to another nrf5340. I am going throw the bluetooth samples, but...
Hi
I'm trying to configure zephyr to build BLE host on the application core and BLE controller on network core on the nrf5340dk.
I was able to configure zephyr to run...
Hello,
I've been having issues trying to add MCUBoot to our application. The app is based on the Common Application Framework (CAF) with a structure based on the nrf_desktop...
hi,
sdk 17.1.0
Can I call " NRF_LOG_INFO" API back to back ? Does it copy the contents of the buffer (var) to an internal buffer ?
For example, in the below code, does...
Hi,
I am using nrf52833 ic with zephyr for firmware development my product is a battery based device and i want to reduce it power consumption when in ideal state what are...
Hello all,
I have pinged the sensor on the "twi bus" successfully, now I am following the post on the read/write function that is needed to actually read the data off the...
Dear nordic engineers:
The only example I can find about flash is under zephyr/samples/drivers/spi_flash. However, the flash writing is pretty slow, and the MCU is halting...
I'm trying to record audio from Nano 33 BLE Sense which is using an nrf52840 microcontroller. But the default PDM library available doesn't allow me to record at a higher...
HI
I would like to check if it is possible to setup 3 sets of nRF5340 Audio DK as a master with two slaves.
Where the master and salves are able to send audio (via mic...
Hi All,
I would like to know how Nordic's pairing mode corresponds to the bluetooth specification.
If my smartphone(initiator) is keyboard display,and my slave(responder...
Hello.
We are developing using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I would like to update SoftDevice from v7.0.1 to v7.3.0. Are there any areas...
