hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I'm using the NRF9160DK board. I'd like to connect the UART port from 9160 to the 52840. The 9160 is running SLM firmware. The 52840 is running my code.
My question...
Some helpful pictures referenced in documentation (asset_tracker_v2_description.rst) are missing:
missing at least: figure:: /images/asset_tracker_v2_module_hierarchy.s...
I am using below environment for my project
NRF connect for desktop version 3.7.0 and Programmer v1.4.11 in windows 10, NRF52840 and Jlink debugger
I have tried multiple...
Hi!
I have a question regarding the scan timeout. The situation is the following:
On a nRF52840, I repeatedly perform scans every 120s (which is controlled by a CC Interrupt...
hi
I am using nr5340 and it adrvertise as nordic_lbs.. but i want to advertise through beacon sample. it still shows nordic_lbs in my mobile nrfconnect software. but it...
Hi,
I am also facing same issue i am able to read the version register correctly and able to perform self test successfully
I am using 17.1.0 n RF5 SDK
I am using SPI...
Hi, my 1-button system off/on example works perfectly fine on nRF52 DK. However, when I move the exact same code to nRF52805, there are some errors.
I choose pin 21 as the...
I've been trying to send fast data with NRF24L01 for a long time. In order for the project to meet its requests, 32bytes of data must be on the Receiver side at a maximum...
At 1M rate, test the reception sensitivity of Bluetooth chip, the number of packets lost at -90dBm exceeded 30.8% as specified by Bluetooth Alliance, and this situation occurred...
hi all, i download the project from github master branch, i also added " pip3 install - r zephyr / scripts / requirements . txt " but still, i got the same issue. i had read...
Hi, I am not sure how to measure the signal strength of the communication within the mesh network (ie. communication between provisioned nodes), in order to verify a change...
Hello all,
Currently I´m developing a code to be load to the SDK to act as a master in a BLE communication. The peripheral is a BLE thermoter that, in order to preform bonding...
I'm attempting to revert an nRF52840 dongle to the production bootloader. This dongle has a SWD connector soldered on for use with J-Link, and I have no difficulties flashing...
