Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
Hi,
I am facing following compiling issue while integrating the buttonless DFU to ble_app_uart code.
I have done whatever this case has instructed. Still i am getting...
I have set APP_ADV_INTERVAL to 100ms. Now when my device is rum=nning i want to manually change it say to 1000ms/300ms.Kindly assist how can this be done for ble_app_beacon...
I would like to use the flash in legacy way. My application collects data in small chunks and I would like to store it in a continuous area.
The recommended flash manager...
I succeeded in implementing the desired function using the NRF52832 development board.
I had to modify the project to include the NUS function of NRF52810. However, it has...
Hello, in zephir/include/drivers/can.h, in can_set_bitrate there is an error - you define local struct can_timing timing, but timing.sjw member wasn't initialized nor later...
In a previous post Related post it was mentioned that the below posted code would allow for a transmission of 20 bytes. However when I try to run this code I see a reported...
Hi everyone,
So I am having this weird behavior when i try to use the PWM with pin(1,9). In my case, i want to do pwm with a number of pin most of them are in port 0 like...
Hi support team,
We're planing to implement the scenario like this. In the mesh network, there are a few LPN nodes (i.e., 10 nodes) and one server node(non-low power node...
Hi,
Just need a quick checking on this.
Currently we using nRF5 SDK, after production, is it possible we OTA update the firmware which using nRF Connect SDK?
This...
Hi,
I tried to build and programm this DTM example from this SDK example: ncs\v1.6.1\nrf\samples\bluetooth\direct_test_mode
I got this following error. Do you know where...
Hi,
With the NRF Connect / NCS SDK, I can build the asset_tracker and serial_lte_modem without issue.
I want to make my own project, so I copied asset_tracker entirely...
Again I am asking a question I should not because I cannot find it documented.
I get a pairing request from the central. I need to respond with sd_ble_gap_sec_params_reply...
Hello.
Now, I'm trying to make a Beacon with updatable Major Value, based on sample 'ble_app_beacon'.
I'm not really familiar with BLE and Nordic device, though...
I...
Hi,
We have created GATT servers and tried to connect with one MOBILE APP.
But, we failed.
Although, we could able to connect with standalone BLE, but once we tried...
