This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I have included PWM library in BLE uart example to control the servo motor. I am able to import the library successfully and able to control the servo. Below is my init_pwm...
Hi,
I would like to know which soft device version is used in my nrf52840 board.
I know it's S140, but I understand that there are different versions for that.
Thanks...
Hi,
I am developing an application based on the aws_iot sample which all works fine.
The application captures data from a sensor and publishes it to AWS.
However, during...
Hello NRF ,
We have been using NRF9160 DK GEN-1 board for NB-IOT and GNSS tracking and able to configure network SIM as well as the NRF cloud .
We have used SDK 1.4.2...
Hello Nordic,
I had to reload a new nrfcloud certificate to my nrf9160DK. An active iBasis SIM card is attached to my nrfcloud account.
I followed these instructions:...
Hi everyone,
I have 1 board normal node(client+server) and 1 board LPN(client+server). I can send message from client of LPN to server of normal node, but i can't send message...
Hello,
I have a design where I am using an nRF52840 along with a SKY66112-11 and am using Zephyr/MPSL for both BLE and Thread. Some questions:
1) The .dts node has pa_gain_db...
Hi,
I was testing the GPS performance of the the thingie91. The default application (asset_tracker) works perfectly, but uses AGPS from the nordic cloud.
The asset_tracker_v2...
Hi all,
We run into a problem where our central product (a remote control) connects to the wrong device. We are using SDK v14.2.0 and softdevice S132 version 5.1.0. At...
Hallo,
I'm using a 52840dongle.
Uart ( PC-Terminal Debugging)
Radio ( reading 51822)
I2C Display
is working well
No i need to write and read data to/from a spi...
I have a serial OLED LCD on my SPI bus on my nrf52840 I want to do periodic LCD refresh by sending it's frame buffer without involving CPU.
I already know how to do SPI...
Hello!
I flashed the light_bulb example(NRF5 SDK v.4.2.0) hex to an nRF52840 Dongle using nRF Connect.
After reset, LED2 lights blue.
I do have an existing Zigbee network...
We have been using ble nus service which is working very well.
There are more than 100,000 bytes of data to be transferred each time.
We were using BLE_NUS_EVT_TX_RDY...
Hi I made some changes in the chat project that is found in NRF Connect SDK and when I build the change project this error occurs
kobj-types-enum.h: No such file or directory...
