Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hello,
Is that true I only need the HFXO to be on right before issuing NRF_RADIO->TASKS_START = 1?
As long as the radio is not in TX/RX status, the HFXO can be turned...
Hello,
I'm writing software for my own board with nrf52840 and SIM800C modem.
I try to connect to MQTT broker. It works when I have TLS disabled or have TLS with certificate...
I'm building a custom system based on the NRF52832 and S132 SoftDevice with SDK 14.2.0.
Our secure bootloader (bonded) is based on examples/dfu/bootloader_secure_dfu. It...
Hello,
I'm working on a project with the nRF52840 PCA10056 board. I want to use Thread protocol. But I'm not sure if Thread supports Coded PHY, a feature of Bluetooth 5...
Hello, I have a nRF52832 DK and a nRF9160 DK and I would like to establish a Bluetooth connection between them and also send data to each other. How can I do that?
Running the Zephyr LIS2DH sample program on a custom board works fine until I configure it to use the trigger and then it throws the z_arm_mpu_fault() error. It doesn't matter...
Dear Team,
chip- nrF52810
I notice a startup current sequence existing for 26ms and the average value is 600 uA. This sequence is present when waking up from systemOFF...
Hi,
We would like your pointers for our following queries:-
1) Would like to know about which firmware stack we can use for provisioning nRF52840 Nordic boards via nRFMesh...
Hi,
I want to do this with nrf9160:
Transmit data (JSON strings) from the nrf9160 to some receiving end, and measure current profile for different amounts of data. It...
Hi,
I successfully send the status of the button from the Switch board to the Light board in the light switch example in nRF Mesh v2.2. .But how can I send other sensor...
Dear community,
we are using nRF52840 (s140) and nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 to develop a multiprotocol (BLE, ZB) application. Regarding the sending...
Hallo,
I try to use app_timer on the dongle to raise an interrupt every 5 min.
The goal is to send the µC in power save mode and every 5 min, it shall wake up, measure...
In the NRF5 SDK 17.0.2 ble_nus_c.c are two calls to the evt_handler without setting event.conn_handle.
Please find attached a patch to fix this for on_hvx() and ble_nus_c_on_ble_evt...
Hi,
I'm trying to figure out what could make the current consumption difference between your blinky example with freertos and with the timer example ?
Here is my configuration...
Hello, this is my current setup: - nRF52840 acting as NUS peripheral, with properly configured coded phy (nRF SDK) - nRF5340 acting as NUS central, with properly configured...
