Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
i have a custom NRF52832 board.
it have a 32mHz crystal but have not 32kHz crystal.
i use keil Uvision for programming, compile and burn the chip.
i use this example...
Hi,
I have been working with nrf5 sdk for my projects and now i am trying to port it into the nrfconnect sdk.
It looks a bit confusing and not able to find the proper...
I developed a custom pcb using the Raytac MDBT50Q-1M module. I tried to minimize the number of components added to the pcb by omitting the external 32K crystal oscillator...
Hi
I am using SDK v15.3 (nRF5_SDK_15.3.0_59ac345). I compiled and tested the MultiLink project.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am tinkering with some BLE configurations specifically related to MTU and throughput optimization, and my question relates to using Notify on my attribute value...
Hi,
I am trying to change the state of a LED whenever there is a rising edge of a button
Here is my code :
When I build, I have this error :
By the way...
Hi,
I am using my nRF52832 with SDK v16 and Softdevice S132 v7.0.1.
My device has the Central role (and Peripheral) and connects to several devices which are added to...
Is it ever recommended to use a PA option in the LTE RF path? Specifically for cases where the device is very remote. For example, this option from Skyworks: www.skyworksinc...
Hi,
I started working on the nRF Asset Tracker. Was able to complete documentation till the Install the nRF Asset Tracker into your AWS account ( nordicsemiconductor.github...
Hello,
I'm wondering if there's a very low power way to detect a mobile network to connect to? Something similar to a carrier detect. Right now, my solution wakes up and...
I took the APGS example and switched in to NB-IoT as I can't easily test with LTE/M at the moment
2021-03-15T16:25:39.226Z DEBUG modem << I: A-GPS sample has started
2021...
Hello! I'm currently working on updating nrf52840 through nrf9160 on the nrf9160dk like this thread and this thread
Currently i have this setup:
On 9160:
I've implemented...
Hi!
In our current project, we have started to use the Connect SDK.
We have a an application CPU with a modem running our main software and uses the nRF52833 for local...
Hi, I am trying to achieve the lowest current consumption possible on the nRF9160-DK, which should be about 1.4 uA in modem shut down state. Unfortunately, my best result...
