Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I continue to be confused by the Nordic setup of projects. There are a bunch of different demos, but what if you want to compile features from different ones?
Specifically...
Hi ,
I have used Calendar example running on RTC2 for my timing feature .
Below are the initializations for starting RTC2 for my clock .
#define CAL_RTC NRF_RTC2 #define...
Thanks in advanced. Both platforms are: nrf52832, sdk17.0.2. The peripheral is based on ble_app_gls and I set static passkey 123456, the central is based on ble_app_hrs_c...
HW: nRF9160 DK
SDK: nRF Connect SDK v 1.4.2
Hello, this is to report a buggy behavior I encountered when trying to implement a BLE-LTE gateway on nRF9160 DK
First...
I want to move the UART on thingy91:nRF9160.
prj_thingy91_nrf9160ns.conf added the following two line.
CONFIG_UART_ASYNC_API=y CONFIG_NRFX_UARTE0=y
The asset_tracker...
Hi All,
I want to use DFU to update the firmware from central to peripheral over BLE , both central master and peripheral are nrf52840.
Central master can find unknown...
Good Day,
we are currently working on a project for university. For this project, we are using esb to transmit a continuous audio stream (i2s format). We sample our data...
I've read similar issues but none with this configuration:-
nRF Connect SDK 1.4.2
Blinky example
Trying to enable RTT logging
nRF5340DK board
Windows 64 bit host...
Hi,
I've come across a situation where when paired to Android 9 devices, the reconnect event that follows waking the peripheral fails. Connection parameters are
The...
For ble_gap_adv_set_configure_req_enc, is the document provided?
I saw " ">infocenter.nordicsemi.com/.../group__ble__gap__app.html" , it was not found.
Hi, There is problem that the including file from "openthread\third_party\NordicSemiconductor\libraries\fds" and already added its path to file...third_party\NordicSemiconductor...
Regarding the data encoding in Advertising, the order of the data is different depending on the SDK. Is there a problem in operation?
The confirmed function is as follows...
We are using nRF52811, is there any sample code support to set/save thread power calibration table/data to available non-volatile partition.
thanks, Webber
Hi there,
Can we please get an updated example for Appendix 5 in this blog ?
Specifically the DFUMaster_SPI and the bootloader_secure_SPIS. Ideally it would be compatible...
Hi!
I was trying the throughput example using two nRF5340PDK boards and I observed the throughput is very low, i.e. 1kpbs. I tried programming the cpuappns, but it didn...
