I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
ble_gatt_db.h and ble_db_discovery.h each contain #defines that are problematic, BLE_GATT_DB_MAX_CHARS and BLE_DB_DISCOVERY_MAX_SRV respectively.
Of course, one can change...
We use NRF52832 in the remote control of the car。 We measured the average current of power consumption at about 1uA.Every 300ms, the current curve bounces to the transient...
I would like to use the RTC in the nRF52833 as a clock-calendar. The device will normally be powered by the USB Vbus but must have power fail protection to insure the integrity...
Hello,
I would like to create a star network (with no routers) in ZigBee with nRF52 (also with multiprotocol BLE). I examined the relevant SDK (nRF5_SDK_for_Thread_and_Zigbee_v4...
My setup is a custom board with the nRF52832 and a remote BLE client e.g. nRF Connect tool kit on an Android phone.
The application periodically broadcasts a 'beacon' but...
I am using Nordic SDK v15.3.0.
I have set all the required parameters and content before I call the API "ble_advdata_encode(..)". I ran into two issues one of which I can...
I am using SDK version 15.3.0 and would love to know what exactly is the meaning of the first parameter "size of event" used in the macro APP_SCHED_INIT(X,Y)?
I treat "events...
I have installed Segger Embedded Studio for ARM V5.32a.
I am trying to build the example project under ble_peripheral/ble_app_uart.
I have installed these packages in...
Dear community, Dear Nordic engineers,
For some reason I cannot connect my custom board to the nordic cloud. Previously I have followed the described procedures with the...
Hello,
I have a custom nrf52832 board with a SparkFun HX711 load cell.
I've developed my firmware using Segger Studio testing my data through a BLE connection with the...
Hi,
I ported my application from SDK 12.3 to SDK 17.0.2. Unfortunatley it isn't running on the board, but the only thing I have is a warning which I'm hoping is the issue...
Hello,
Let me start with some background information and end with some questions.
Background
We are using the 9160 in cat-m0 and locking to AT&T and Verizon bands...
How much is the temperature characteristic improved by setting CALIBRATE OFFSET for nRF52832? How much does CALIBRATE OFFSET improve the temperature characteristics?
Are...
Hi. In other discussion I have seen pairing/bonding should store all necessary parameters of a discovered service. It's possible then to reconnect to a bonded device without...
