Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
我正在执行ble_app_uart_c例程的功率测量，并且已经关闭了串行端口，这与打开串行端口时测量的波形不同。 我猜封闭的串口会影响扫描。
This is the waveform without closing the serial port
This is the waveform without serial port...
I add a compiler flag --wchar32 i n the Misc. Controls section of C/C++ to support character pointers with 32-bit width. But got errors as log attached. Any help is appreciated...
Hello guys,
I am a newbie with nrf52 and I am trying to debug ble_app_uart project under ble_peripheral directory. I do get download successful as shown in image below...
Hello,
I am trying to use the PPK (I) to measure current consumption of a DVK-BL654. I was able to successfully do this several months ago, and now when I am attempting...
Greetings,
I'm having some trouble displaying logs to the SES Debug Terminal... Basically, I can see the logs with RTTviewer but not in SES Debug Terminal. However printf...
We are in the process of applying for approvals testing of the device and need your help to confirm the following. Bluetooth data required (we use BLE4.1 mode): 1) Operating...
I need to apply for timeslot to scan private 2.4G signals, in order to save power consumption, the timeslot needs to be ended immediately after scanning the signal.
I try...
I'm using a custom board designed around this nRF52832 module . I have broken out SWIO/SWCLK/SWO and nRF_RST to a standard Arm 10-pin header.
Using Black Magic Probe, I...
Hello All,
I am trying to Program our custom board which has nRF52 controller using nRF52- development kit ( https://www.nordicsemi.com/Software-and-Tools/Development-Kits...
As the title says, I'm getting a hardfault on a call to pm_init() in a BLE peripheral HRS trial application. This is on a micro:bit v2 board, which has an nRF52833 Cortex...
Hi, Im trying to add accelerometer value to my own service. The device is advertising, When I connect to the nRF Connect application, I can not see my service, the status...
Greetings,
I'm using nRF52 DK to transfer LIS3DH accelerometer data in Bluetooth. I successfully managed to establish an I2C connection with my sensor, I get my XYZ values...
Hello Nordicsemi Community,
I am attempting to update the firmware of nrf5340pdk cpuapp from a mcumgr cli running on a raspberry pi 4 linux. From the logs, it seems the...
Hi,
i am using a nRF52840 with sdk v17.0.2 on soft device s112. using the ble beacon example. i can set up the connection from the raspberry pi with a 2 second beacon...
