Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello,
I wanted to confirm my understanding of the Replay protection cache. In the code, the limit is set to REPLAY_CACHE_ENTRIES and there is a note that says:
@note...
Hi to all.
I am new to this forum and to the Nordic range of products.
My experience over the last few months have been with arduino and Feasycom bluetooth modules. I...
Hi,
Since I updated nRF connect from 3.6.0 to 3.6.1, I get this error when I try to connect to a device :
"Error when getting device info: Error: Error: Error occured...
Hi,
I'm trying to devise the hardware platform for a Home Monitoring medical device. In the first place I planned to use the NORDIC nRF5340. With its large memory it would...
Hi.
We have a debug board for the NRF52832. The breadboard on this board is working fine. But if NRF52832 is used outside the debug board, then for some reason, some phones...
I want to set the Device's current date and time as I have to check time after certain interval. I don't want to use RTC where we have to look for ticks.
My questions...
Hello,
Could you please let me know if any of your devices would be suitable for our specific configuration?
We have a WMware server running many VMs. We would like to...
hello i am using nrf52832 and mpu6050 accelerometer with sdk 16 while programing i used 27 as scl and 26 as sda which is default in nrf52832 and i had no issues while reading...
Hi,
I am trying to test the light_lightness example present in ' nrf5_SDK_for_Mesh_v5.0.0_src' , on nRF52 Development kit(pca10040). And i am provisioning the device using...
I have a production device which I have soldered an SWD connection from a Keil project via the nrf51822 DK (port 20). I can flash code to this production device, but I cannot...
I'm using a SPI with a circular buffer so i need to have an interrupt with low latency that reset the RXD.PTR when the buffer is full.
The SPI is used for communicating...
Since Zephyr’s official BLE sample code, his BLE central only supports one central to one peripheral So I refer to the BLE central multulink officially provided by nordic...
HI ,
My name is MOHAMED ALI SAIDANE from Tunisia , i've been working on my project of the last year eduction , i'm interresting about the concept of the module NRF24l01...
We are using a custom ARM board which runs Linux and has a UART interface to a nRF9160.
I'm not how to phrase this exactly so I will just describe what I would like to do...
