Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Hello,
I want to to configure mesh proxy node and along with that it should also contain relay functionalities using nrf5_SDK_for_Mesh_v4.1.0_src.
Is there any sample...
I'm seeing some issues I don't understand when using RTT. Here is a short fragment of code around the RTT_Write statement.
The commented out statements are included while...
I am using nRFConnect with nRF52840 Dongle. Since the last update to SoftDeviceAPI v5, nRFConnect cannot connect anymore to this specific devices (cheap JDY-10 BT/Serial adapters...
Hi, I want to store some personal data through flash in the LPN mesh routine. I read some posts and can be implemented by using flash manager, but I can't find the relevant...
Hello, I am working on storing words to flash using fds. I am working with the nRF52 DK and SDK V15.2.0. As mentioned in my earlier post , I am storing some critical state...
Hi,
Greetings!
I am using below setup:
SDK: v16.0.0
Mesh SDK: v4.0.0
Application: Light switch server and client
Hardware: nRF52DK
Distance between client and...
Hi, I am using ble_app_uart example for peripheral device and it will be powered by a 3.7 V battery. I need to use battery as long as possible. So I decided to make peripheral...
When I put the device into sleep it draws app 30 uA in sleep mode. Read in the manual: "Core standby current= 50 μA", "Current drawn if HFXO is forced on through for instance...
Hi,
I am trying to emulate a vendor's tool, whose BLE properties are configured as follows: Custom 128 bit Service UUID like XXXXXXXX- 0000 -XXXX-XXXX-XXXXXXXXXXXX
Custom...
hi, I am working nrf52832. I am making configuration file for nrf52.so I want to used Led3 set as high.
#define LED3 ((GPIO_PIN_CNF_SENSE_High << GPIO_PIN_CNF_SENSE_Pos...
Hi, I am looking to access nRF9160 modem via I2C. Essentially looking for hooks/ serial interface hand-off points used for instance in AT Client sample or Serial LTE Modem...
We have some devices out in the field with a mixture of application versions. In one particular case, we have device A on application version 10 and we have device B on application...
Hi there
I am having issues to perform disconnections from my central device when calling sd_ble_gap_disconnect()
most of the time I am able to disconnect properly using...
Hi Devzone:
I am researching how to maximize radio performance and stumbled on a statement on page 356 in the spec:
"Typical sensitivity applies when ADDR0 is used for...
Hi! Currently I have a nrf52840 devkit hooked up to an SD-card for storage through FATFS (using SPI). I would like to add a BME680 environment-sensor to the board and have...
