Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I try to write some data into the flash memory, but I always get a hardfault when I try to use the write function provided from the examples:
No I think this...
Hi everyone,
I am trying to start a data length update procedure from a central that I am developing with python using the library pc-ble-driver-py.
However, I keep having...
Hi,
I try to store some variables into the flash memory using the fstorage library provided by nordic. From the example I got the following implementations for testing:...
As I mentioned in my other question , I've been playing around with the bearer layer of the Mesh-Stack, to get a better understanding of how to get a robust basis for a multiprotocol...
Good day! Tell me how you can configure access to UART with DMA in the example freertos_coap_server for receiving and transmitting arbitrary messages. Also, please clarify...
I am using this sample https://github.com/NordicSemiconductor/Android-nRF-Blinky . I noticed that when device rotation is changed the device stills connected.
I changed...
Good day. I can't find the schematic of the EVAL NRF52-DK version 2.0.0. The previous version I used was 1.2.4 where I cut the following welding points for testing.
SB22...
I am able to log information to the flashlog backend. When I use the cli interface "flashlog read" I see my information stored (e.g. "operation took %s seconds to complete...
I am trying to download the NRF UART and Nrf Toolbox service the same ones used in the playstore are different than the one on github. The NRF UART v2.0 is different and doesn...
Hi,
I setup one ble mesh network, and it works good for a while. But I encounted a problem that when I power off the mesh node (note: the voltage drops slowly) and then...
Hello,
I am working on nRF51822-QF-AAFQ chip using SDK 12.3.0 in IAR embedded workbench.
My question is, can I impliment DFU in nrf51822 chip?
If possible suggest Starting...
Hello All,
I am trying to add DFU service in the small example with the custom service.
But is not working, facing issues.
I am working on the nrf52810 board with...
Hi all
I am trying to pair nrf52840 (as a central) with ESP32 (as peripheral).
Now I want to get the service uuid so that i can pass to advertising service in ESP32 code...
When restrating the controller, are there any information stored in memory regarding the paired devices or is this up to each implementation to do this manually.
1. If there...
Please tell me about AFH (Adaptive Frequency Hopping).
SDK：15.3.0 例：ble_app_multirole_lesc DeviceA：EYSHJNZWZ（nRF52832）
In AFH (Adaptive Frequency Hopping), the frequency...
