Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Question: for the nRF52840, if I configure a GPIO pin as an open-drain output (DRIVE setting of S0D1) and then select this pin as a UART transmit pin, does the open drain...
1 .after the flashing the board i get a Zigbee Connection and Bluetooth connection but i can't able to control the bulb by using both board and bluettoth
2. Sir i am using...
Dear all.
I know the nRF52840 has 2 uart module.
I've been used only 1 uart setting like below pin connecting in 52840 DK reference doc.
But now i have to use 2...
*** Disclaimer *** I am a total rookie on this technology *** Disclaimer***
I'm working on a small BLE proof of concept and I have an nRF52840DK board. I've got Wireshark...
Hi, guys! I'm using the nRF52 SDK 15.3 BLE_APP_UART peripheral example.
I wish to add 3 ADC channels (12-bit) to read 3 potentiometers at a sampling frequency of 6kHz. ...
Hi,
I've BLE custom data sent to nrfcloud and looking for ways to plot data. I've used "add custom card" from configuration to extract data but was not able to plot/view...
hi, I am working on nrf52832 platform and tested some Bluetooth examples of SDK_15.3.0, I want to test some Bluetooth examples like audio, media and etc, is there any project...
Hi,
I am using a BLE master to bond with nRF52832. SDK is 15.3.0. Both side support secure connection.
I have tried to set the address type of master to public or random...
Hi, I'm starting to use the nRF52840 DK, I have downloaded the segger embedded studio but I don't have idea how to start, I need a sample example to use the pins to control...
I am new to Nordic products. I have a custom nRF51822 board and I want to flash it with Keil uVision and ST-Link V/2.
As I understood, I have to program the SoftDevice firmware...
I'm implemented DFU (with custom transport, but the problem is not there). Even when flashing SD+bootloader+app+settings I can see an error in the logs:
```
14:23:48.096384...
NRF Connect sees the devices no issues and connect. When it comes to running any of the examples in the toolbox, the devices are never seen. Location services are allowed...
Hello,
one small question: If we switch from Softdevice S132 6.1.1 to 7.0.1 without recompiling the application or using a higher SDK, does it mean, that we will automatically...
To measure the current consumption of our external battery powered device I plan to do the following (as described in chapter 6.6. of the PPK User Guide v2.2, Figure 14) ...
