There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx(the send length is fixed 10 bytes) ...
Dear nordic employee:
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi all,
Last year, we have successfully developed main app with bootloader without SoftDevice on a custom board using the nrf52840. The starting address of the main app...
I have the following problem in my app:
Connect with BLE
Using the device works
Disconnect
Connect to BLE Device
Start Gatt.DiscoverServices()
Android does...
Hello Everyone,
We are using nRF52840 DK with Segger Embedded Studio (SES) using SDK v15.0 We are sending few command to sensor via SPI for reading sensor value. But while...
Hi everyone,
I have some questions / problems about the advertising report in the nrf52832 dev board. I'm using the example code from here : https://github.com/NordicSemiconductor...
Hi,
I've been implementing the BSP functions on a 15 button custom device based off of the nRF52832 (in a BL652 Laird Module). At a minimum I need to be able to disconnect...
Dear support team,
I'm using the demo ( thingy52-mesh-provisioning-demo).
I want to create an opcode hadler to enable/disable proxy service.
So that I can send messge...
Hi for my use-case I need the RTC in the NRF51 SoC to run continuously and uninterrupted (we know running out of battery will be a concern). Keeping the NRF51 system on 24...
I need some example code to write vendor specific service on latest development kit i.e on nRF5_SDK_15.3.
There are couple of example codes available, but in particular...
Hi
We want to put the processor in deep sleep, with minimal power consumption. When we measure, we see that the SIM is powered throughout the sleep period. Is this normal...
Dear All,
I am using the nRF52832 in conjunction with a W5500 SPI-Ethernet controller by WizNet. I already implemented a TCP server, a DHCP client and an MQTT client by...
Previously I used the MQTT example and connected it to our own server successfully. However, I want to do the same for the asset tracker application latest release (v1.0.0...
HI
I am using nrf52832 modules with SDK 11.0.0, s132.
I am able to advertise and scan the devices and display RSSI and peer address.
For my project i want to display...
Hello,
I am trying to configure a UART to use in the nrf9160. I am using zephyr's uart.h
This is a snipet of the code I have right now.
Code as it is executes successfully...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...