Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
HI, I am using NRF52832 sdk15.2 .
I have some doubts
How to assign two to three different timers to do different functions
1. I need to read the sensor data every one...
Hello,
I'm working on a BLE central project where we want to utilize LESC Just Works Unauthenticated pairing.
I followed the recommended usage guide at https://www.nordicsemi...
Hi,
I am using nrf_fstorage_sd which uses nrf_atfifo. I would like to know what it is max usage of m_fifo queue so I can set lowest NRF_FSTORAGE_SD_QUEUE_SIZE value. I figured...
I develop an program with BLE DFU support, but we hope to merge all hex as single hex file. Then we can burn this hex file by programer (such as jlink or NRF52DK), So we have...
Hello,
I'm trying to run the s132 (and s140) softdevice while running a proprietary mesh network stack. Naturally I'm requesting a hefty amount of radio slots. I need to...
Dear Nordic,
I have an application which contain UART and BLE advertising. For power consumption i use enable disable UART.
Enable and Disable Uart:-
Is it right way...
hi..
i am using nrf52832 and a peripheral device .. temperature sensor ,my temperature values are increasing like(0 ,27,75,80...) how to get a approximate value .
i have...
Platform: nRF52832 using SDK12.2 and Keil 5.20a
I've encountered strange corner case when displaying negative floats using NRF_LOG_DEBUG .
My test code looks like this...
I want to use BLE 4.2 Data length extension to stuff more data into one packet. I am looking at the "ble_app_att_mtu_throughput" example and am getting confused because there...
Hi!!
I am sending data by BLE data received by SPI.
The interval for sending data at BLE is 64 ms.
I have written and run NRF_SPI 1 -> ENABLE = 0; and NRF_SPI 1 -> ENABLE...
can't open 'J:/Projects/..../Electronics/SDK/BT840F/nRF5SDK15209412b96/nRF5_SDK_15.2.0_9412b96/examples/ble_central_and_peripheral/experimental/ble_app_att_mtu_throughput...
If there are multiple beacons, let's say B1,B2,B3,B4,B5 and a BLE receiver. I want receiver to only wake up from sleep mode when B1 transmits(long broadcast interval) and...
Hello Nordic community,
is it possible to configure the network key, application key, node address with the help of a byte array? The keys, adresses and all the peripheral...
