Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm trying to create an automated script for deploying the command line tools with the segger Jlink driver.
I'm currently using the 9.6.0 installer with the following command...
So I reinstalled one of my Linux boxes (again) a few days ago, and one of the things I need to do to get all the development environment up and running (again) is get the...
Hi everyone,
I'm currently working on MAX30100 sensor and i need to read this sensor data with i2c, currently i'm able to read mpu6050 and 9255. However i don't have much...
Hi all,
My BLE device uses the NUS profile to send data to a connected smart device. At the same time it should also be possible to connect to a RPi/Linux based gateway...
I now use nrf52832 to do development, nrf52832 and mobile phones to transfer the data is relatively large, I would like to achieve For mobile phones that support BLE4.2, a...
Hi Everyone,
I have been experimenting around with the low power SAADC example in SDK13.
I am using PCA10040 dev board and I have programmed it to start/stop ADC sampling...
Hi,
We've been developing an peripheral HID over BLE using Nordic's SDK, connecting with iOS, Android, and Windows devices. (Board: nRF52832, SDK 14)
We've noticed an...
Using 2.0.0-1.beta on Linux Mint 18.
Have installed pyserial with: sudo pip install pyserial --upgrade --ignore-installed
resulting in:
Installing collected packages...
hi ;
now after i maked a successful connection between smart phone and nrf51822 and i could change the state of gpio pin 20 i find a new problem
i want my pin is still...
Hi All,
Just wondering if i'm doing the right thing here.
So i am using the example of the central device to get started.The idea i'm trying to do is to use the central...
Hi,
I am working on my production hardware with nRF52840 on it. I am using MBED OS. What should be the memory map of 52840 for soft device and Application code? I am using...
Here are my system requirements:
A single "Controller" needs to send 4 bytes of data per node.
There are 25 nodes in a system (100 bytes total payload).
All nodes must...
Hello,
Is it possible to use Mesh SDK and create a GATT database for mobile device to connect to? There are no examples for this in Mesh 1.0.0 and 1.0.1 except a simple...
Devzone,
I'm working with the nrf51822 dev kit- specifically with master emuator API version 2.1.8.
Does this current release of the API (2.1.8) or subsequent releases...
