Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
I did some power measurement on the nrf52 DK with the Nordic profiler kit and the result was way more than what we could expect from a nrf52 (about 1 mA). Even in...
I am working on the ANT connectivity for a product we've developed, called RunScribe [a shoe-worn running sensor], and am seeing some issues on Fenix 5 watches with our ANT...
Hi,
I'm trying to implement run the ESB and the BLE concurently using the timeslot API.
I started from this example : devzone.nordicsemi.com/.../
The problem is this example...
Hi,
I'm quite a beginner to this whole nrf52832 world and I'm trying to read some data from a flex sensor wired in series with another resistor connected to VCC now I understand...
In brief our problem with rfx2411n is that rfx begins to draw 200ma current without any reason. Rfx is powered down, powered from 3,0v. And suddenly something happens and...
I have a device that runs with nRF51 chip with the NRF UART Service (NUS).
I have a Raspberry Pi 3 and I want them to communicate.
The device requires an authentication...
My question is related to peripheral device only. I have implemented an auto connection interval negotiation algorithm which works as expected and negotiates connection interval...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Hello sir,
I have completed PCB design of custom nRF52832 board. Can i use following component instead of recommended part No in reference design. I have also mentioned...
Hello ,
I would like to design a custom board with nrf52832 IC and CP2102 for communication with PC serially. Unfortunately nrf52832 doesnot have Rx/Tx pins for interfacing...
Hi community,
for our application (nrf52832 / SDK 12.2) we need to store data received via BLE. The received data is a 25 kB binary blob which by design will be chopped...
Hi,
i am checking NRF52840 for USB behaviour.
I'm using example usbd_cdc_acm.
But USB receiving stucks after few bytes (between 0 and 50) and does not receives nothing...
i have nrf52 dk i run simple examle saadc from sdk 12.1.
now i want to get result.
i can't understand the code.
i start putty terminal adc event number and app info number...
I'm having trouble adjusting ram start setting using the new SES projects from latest SDK14.1.0
I have tried the project linker section placement macros settings of
...
