Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
We've developed a prototype for a client and just received the nRF51 chips for production. Problem is that the chips that just arrived is an older revision than the...
Hello, I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated Continuous...
Hi all,
I'm having a tight deadline upcoming and have run into an anoying problem.
I'm using this NRF51 breakout board: ohtcom.com/.../nrf51-m0-module
I ordered a...
HI I am trying to make 5 characteristics on Nordic and my program does not compile for NRF51822 QF AA or AB. but compiles fine for QF AC. what could be the matter. I get an...
Hi,
At command, I'm sampling ADC for a short period of time. What I noticed is that the current consumption of the chip goes up 2mA, even after the sampling is stopped...
Hi,
What is the actual difference in hardware between the two chips? I know they support different soft devices but is there any actual difference in the hardware? Or is...
Does having monitor mode debugging or using RTT print statements increase the quiescent current of the nRF52 even when the debugger isn't connected? I am using S132 SoftDevice...
I'm in the process of porting code from a PCA10000 rev2 board to a custom board, using the ISP130301 integrated MCU (contains a rev3 nrf51822 IC). I'm using nrf51 SDK 6.1...
Hi,
I use an nRF51822 QFAC A1 and my goal is to disable BLE in a powerdown mode, then when I press the pushbutton I want to restart BLE.
Tried using BLEDevice::shutdown...
Hi,
I'm using nrf52 dk(PCA10040). I want to disable the SAADC between readings to save power. I am calling the function nrf_saadc_disable() to do so. It seems to disable...
Hi,
I am having some trouble to make NFC Tag emulation working with "ble_app_hrs_rscs_relay" example application in the nRF5 SDK v11.0 on a PCA10040 board. Actually I did...
Hi all,
i have a little problem with the #define NRF_LOG.
I have this warnings, and i don't know why.
Warning[Pg004]: macro parameter " VA_ARGS " is used in both expanded...
Hi,
I would like to generate PWM waves with on/off period as low as 10usec.
How to stop the PWM and restart it? I tried this but does not stop the PWM:
void pwm_start...
I am trying to advertise my eddystone UID,TLM and URL frame on advertisement. Here by board is in peripheral mode.
I used radio_notification_init() function where i have...
