Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Every 10 packets send; it will have at least 1 packet with 1-2 bytes corrupted data.
The configuration as below:
data rate: 2Mbps
channel: 7
Prefix0: 0xE2
BASE0...
Hi,
We have an application that can run in two modes. The mode is selected by setting the GPREGRET to 1 or 0 and restarting.
Currently we are running this procedure directly...
Hi,
We are developing a product using the nrf 51422 where the power source is a 3 phase generator.
We rectify and charge on a supercap where the uProc is being supplied...
Please correct me if I'm wrong but my understanding is that unused RAM banks can be disabled to reduce quiescent current.
My first question is what is the current consumption...
Hi,
I'm using RTT debugging with soft-device " https://devzone.nordicsemi.com/tutorials/6/debugging-with-real-time-terminal/ " , I'm able to print few messages, after which...
Hi~ I'm sorry because it usually does not use English writing in English, So there may be errors in English please forgive me.
Last year, I bought some nRF51 Development...
Short: Working Timer. Working SPI. SPI does not work when triggered by timer_handler.
Hello,
I am currently trying to replace delays with timer in my code...
I set...
Hi.
I'm using PCA10028, SDK10.0.0 S130.
I want to make nRF51 goes sleep mode.
So I tested linked source code as below.
github.com/.../main.c
It works well.
But...
Hello, Nordic Stuff.
I've been working at ble peripheral devices using S110.
I am just wondering why the sd_ble_gap_disconnect function accepts only the reason code...
I am interested in developing an nRF51822 application for an old PCA10001 nRF51 evaluation kit using a Mac OS X platform. I've downloaded and installed the following tools...
Hello,
I have a nRF51DK.
I am trying to use the TWI driver to communicate via I2C with an accelerometer MMA8452Q.
I already have a working code based on several SDK examples...
How much additional current does enabling the FPU add to the nRF52 processor? I reviewed the Product Spec. but I can't seem to find this listed anywhere.
Thanks
We successfully used the pofcon on a 51822 based design using S110 ver 7 to indicate a low batter condition to the user. However, we are moving to 52832 (currently QFAA-BA0...
