hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
In my application, I would need to use both RTC(function as a timer) and Watchdog(as watchdog). Is it OK?
I saw in the manual "the watchdog will automatically force the 32...
my purpose is to use the 51422 or 52382 as a central role to search my own service, or any other SIG standard services.
DK :nrf51422 ,
version : 9.0.0 and 10.0.0,(i...
I m developping an iOS application, and I need to integrate the DFU part.
I found the IOS-nRF-Toolbox , but what I need is to integrate only the classes that manage the DFU...
The nrf52 with SDK 0.9.2 SDs132_nrf52_2.0.0-4.alpha_softdevice has 3 TX_buffers(2 count can i used).
I think there may be some preserve TX_buffers for BLE central or ANT...
I'm working with nrf51 board, I'm using I2C to communicate with an accelerometer (see the scheme), the communications are successful but I dont see any pull up resistors in...
Hello there, this is my very first post here.
I have a pair of nRF24L01 modules with built-in PCB antenna, I would to know if is possible to obtain the approximated antenna...
I have the nRF UART-over-BLE examples working on nRF8001 & communicating with the corresponding Android App as "host".
Instead of the Android App, I would like to use an...
Hi
I have a problem using TWI driver with my softdevice enabled.
The TWI is able to communicate successfully to the slave without the softdevice.
But the same code...
Now that my application finally supports OTA DFU, I hit a new problem. Instead of nRF51822 starting the newly flashed application, some old version seems to start. Or at least...
Just a general plan not a detail one . like this: in the SD132 2.0.0 we will add the funtion of change the MTU up to about 150 bytes，at the approximate time 2016-4
I am testing the freertos port, based on the hrs example in the new SDK 10.0. I have run into an issue while using the uart during long transmission sequences (where the fifo...
The alpha release of the S332 is now available and I am just curious which example included in the 0.9.2 SDK would be the best jumping off point for building a new project...
I just realized that I have the nrf52 board (with nrf25832) which actually explains a lot but the end goal of my project will be using the nrf51822 (because the nrf52 chip...
Hi there,
I am using the nrf51-ble-driver_win_0.5.0 to communicate with peripherals via the PCA10028.
My problem is when I call sd_ble_gattc_write() in my Windows application...
