Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hello,
I'm looking at nRF51822 as the BLE solution in a peripheral device which will have a number of different functions/features, some of which require a modest amount...
Hello,
I see a master control panel software that can be used to control a PCA10000 USB dongle for BLE applications. Is there such a Sensor simulator application for the...
Do you think I could update PCA10001 V2.0.0 just by replacing the nRF51822 chip? I have more current chips lying around, and with a little rework I could be able to switch...
When writing a post in this forum, I found it somewhat nice to have a preview before I do submit.
Even for questions, answers, comments and pm. May it possible to enable...
Hi
Is the generic attribute primary service 0x1801 added by the soft device?
Bluetooth standards say that the service changed characteristic is optional. I am using...
Hi sir
According to nRF51822 RM v2.1 session 12, there are two high frequency clock: the 16/32 MHz crystal oscillator and the 16 MHz RC oscillator. For nRF51822 BTLE application...
I know the question has been asked, but a few months has passed,
but hopefully to get some new update now.
devzone.nordicsemi.com/.../nrf51822-dk-module-as-master
devzone...
Hello,
i try to implement a simple timer interrupt on TIMER1 using one of the CC registers of the NRF51822. Here is my code:
void init_timers(void) {
// Start 32...
Hi,
I have 2 questions regarding this topic:
Which specific J-Link lite mode do we get from nrf51822 Development Kit? Is it the 9 pins model or 19 pins model?
...
Hello,
I want to implement a proximity central. At the moment, I do not get a bonded connection from central to proximity peripheral (For peripheral i use the proximity...
Hello all,
I have realized my own board with a msp430 microcontroller and a nRF24L01+.
I have configured my nRF24L01+ as described in annex C of the datasheet; the objective...
Is it possible to use the J-link to debug a stand-alone PCA10004 ? I am not using the motherboard. Powering the board separately. When I try and run debug in Keil I get error...
I would like to ask a question about the time of :"Time between DISABLE task and DISABLED event when
the radio was in TX" of the "Jitter". In the picture show the "Jitter...
