I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello,
I'm trying to erase/read an external flash ( MX25L6433F) connected to an nrf52840 using nrfjprog. I've created a .toml file for the configuration, see attached. The...
Hello,
With the nRF5340 LE audio application comming with nRF Connect SDK 2.6.0, I found an increase in the audio latency compared to previous versions. I was able to measure...
Hi,
I'm implementing flashing modul, which will be running on external mcu. Therefore for the very 1st step, I have captured traffic while performing dfu on PCA10040 via...
Hello,
Do you have an example that allows you to use the “Service Changed Characteristic” on the server side?
In fact, I saw on the internet that on IOS, we have to use...
Hello,
I am trying to generate encrypted data of particular data with IV and Key value by using mbedtls functions but when I try to do that in AES_CBC example code I am...
Hello,
I have multiple nrf52840 devices ( PCB's ) that act as peripherals and advertise data in BLE 5, and connectable in BLE 4.
We are able to connect to the device using...
I'm trying to enable DFU on our device but am getting a lot of issues.
I used Device Manager to upload app_update.bin and it worked. If I use Flutter example to upload firmware...
Hello everyone,
I am currently evaluating the nPM1300 Fuel Gauge with a LiFePo4 battery.
I would like to use nPM PowerUP to prepare the battery profile, but it appears...
hi support team,
i was testing mcumgr ota from uart, but found that the speed is slow how can i improve this?
i have change uart baud to 460800, but did not help. for...
Hi,
I'm using an nRF52840 DK to develop my prototype. Now I'm moving into the PCB design phase and I'm using a BLE ceramic antenna. I'll add a pi network footprint to tune...
I am using SPIS for my project. I am manually toggling CS for the peripheral. I get NRFX_SUCCESS for nrfx_spis_buffers_set() function. Also, when I probe the CS signal on...
Hi,
I am using the nrf52840 dongle board just to startup a project. I connected to the dongle a UART-USB converter to the dongle... but when I enable the UART into the firmware...
Hi Sir,
Please help to check do we support the ISO14064/ ISO14067 for the below part numbers.
1. Could you help to check do we pass the ISO14064/ISO14067?
If yes,...
