I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi,
I'm working on a project with the Nordic nRF9160 Development Kit and am trying to send Bluetooth beacon data from the nRF52840 chip to the nRF9160 chip using UART and...
Hello,
I try to enable the LE Data Packet Length Extension. According to the available documentation, it should be as simple, as adding `CONFIG_BT_USER_DATA_LEN_UPDATE=y...
When loading empty software (zephyr based) into the nRF9151, the nRF9151 uses roughly 4mA and when erasing the IC, it uses 5.8mA.
Does zephyr not include a power down mode...
Hello!
I am porting a nRF Connect v2.9.0 application from a nRF52 to the nRF54L15.
We are using PPI/EGU to get exact measurements for some BLE radio events for some optimizations...
Hi,
We are developing application software on the nrf9161dk that uses the little FS file system running on external FLASH. Most of the application development has been completed...
Hi
I want to use P0.18 gpio as output pin and not as reset for nordic.
I am using ncs v2.0.0.
I have added
CONFIG_GPIO_AS_PINRESET =n in prj.conf
and when i...
Hello,
I have a Nordic Thingy:91, and I need to perform continuous wave (CW) transmission tests in LTE. To achieve this, I plan to develop custom firmware that alternates...
Hello Everyone,
We are working on a new product using the nrf52840 and OpenThread.Our current product uses the Azure IoT Hub and we were wondering if we could use the library...
Hi,
I defined __STACK_SIZE as compile/build flag. It has no effect according to GCC output after building is done.
Chip is nRF52840.
I tried to set fixed stack size...
Based on the message on the following page, nrfjprog has been deprecated and should no longer be used:
https://www.nordicsemi.com/Products/Development-tools/nRF-Command...
Hi,
I am nrf52dk/nRF52832 (512kB flash) nordic peripheral_lbs sample as a test environment for establishing OTA updates. In my product firmware, I am facing a situation...
Using nrf5340 with nrf7002 on a custom board, and trying to get a stable wifi operation (including in situations where the wifi AP availability will vary, as this is a mobile...
Hi, I having a hard time with SAADC using v2.6.1 and a custom board. I have built the samples and gotten hem to work on the dev kit. I am trying to apply that to the custom...
