I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Dear Concern,
We were developing one of our products using nrf52840. We previously used the nrf-52840 USB dongle for the product. Now we were moving to nrf52840 chip based...
Hi,
nRF5340 + nRF21540, NCS2.0.2, VScode
i follow Working with RF front-end modules — nRF Connect SDK 2.0.99 documentation (nordicsemi.com)
how to disable TX_EN? i only...
Hi,
I am using SDK 16.0.0 and nRF52833. In which TWI (master mode) is not working.
Pressure sensor is connected over I2C. (NRF_DRV_TWI_INSTANCE(0))
Previously I am...
Hi to all!
I'm trying to use the same GPIO to wake up the nrf52810 from system off and also use it to execute some functions. I have this code that is based on the example...
I'm trying to load a program to a custom pcb with a n52832 chip, but shows up this error in the Programmer: Failed to load readback protection status: async task failure for...
Hello,
I am working on a project that modified from ble_app_uart_c, with sdk v16.0, softdevice S140
In my case, I defined an event observer by
NRF_SDH_BLE_OBSERVER(m_ble_observer...
Dear Mate,
I am using bl653_dvk board i followed this link clearly (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi...
I am working on a project that need to receive extended advertising data, I modify periodic_sync from nrf connect sdk to get the data and it works for my device, but I need...
Hello,
I am testing current consumption of my custom board with PPK. There are some passive components (resistors, mlcc) on the board also with active components (accel...
Dear Nordic,
I want to scan slave devices , so I use TWIM nrfx driver to send zero byte data, I don't got error code, but I don't receive TWIM event too. I found a example...
Hi everyone,
I want to design PCB for nrf52840. Do you have any suggestions before i start?
I used STM32, PIC, Nuvoton and Atmel series IC's in my PCBs. But nrf52840...
Hi There,
I am working on a Door lock system using Nrf 52840 Chipsets having BLE and ZigBee Communication protocol. I wanted to have ZigBee OTA DFU feature in my product...
Hi there,
We are seeing a massive difference in UART current between the same revision 2.0.0 nrf5340 devkits. Below, with the UART enabled with HWFC and only the receiver...
