Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Using a NRF9160DK. SDK2.0.0. Modem 1.3.2.
I have a problem when setting up a new NRF board to run with MQTT with AWS.
When the setup is running, I get LOG <inf> for...
Hi,
we have a unit that needs to go for conformance testing.
The only external interface we have is the nNR52833s USB port (pins 12/13 on QDAA).
Alternatively can the...
Hello,
We're using a nRF52840 with S140 SoftDevice (v7.3.0) for a Central device but we're having a disturbing issue when scanning: a hardfault occurs less than 2 seconds...
Using the pc_ble_driver_py.ble_driver I'm able to subscribe to notifications, but unable to get the values upon connection. The error is:
I do not know how to install...
We have an application where we need the PWM pin state to revert to high impedance between bursts. It doesn't appear this behavior is capable by default. Is there a means...
Hi,
As mentioned in the question, I want to use the external clock as the RTC instead of the internal clock. How to configure it?
Platform: Windows 10
NCS version: 1...
For a fully connected set of node devices in a BLE mesh network, where any node device can send data packets to any other node device via an optimally short number of radio...
Hey,
upon a BLE_GAP_EVT_ADV_REPORT I call the following function:
static void pass_adv_data(ble_gap_evt_adv_report_t const *p_adv_report).
The function checks the p_adv_report...
Hello,
I'm having trouble setting up CMSIS Configuration Wizard in SES IDE v5.50a on Mac OS.
I've followed the instruction in https://www.youtube.com/watch?v=b0MxWaAjMco...
hi Team,
working Environment:
nrf52832 DK, SDK 17.1.0, keil IDE uvision 5, Windows 10 pro.
i am working with ble_peripheral based ble_app_uart example.
this program...
I am working on some teching modules covering MCUBoot and DFU ... and trying to get the
basic examples built for an nRF52840 DK board ... and am running into an error along...
Hi,
i am using MCUBOOT + nrF5340 and i am using the nRF Connect Device Manager to upload firmware and perform the upgrade.
I would like to know if it is possible to execute...
How do I check to see if a peripheral is inside the list of bonded units of a central?
I know I can just scan -> see unit -> connect -> change security and if it IS bonded...
Tried debugging and found the code loops in this place, lfclk_spinwait
I have added the following configuration in prj.conf
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
With our nRF52832/52840 products, the UART sometimes drops characters.
I'm using nrf_drv_uart (SDK12) with two, one-byte buffers, and an interrupt called when data is received...
