Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hi ,
I have my own custom nrf52832 pcb. I have 2 chips on my pcb.
I program my device with Nrf52 Dk.
When I program MCU 1. The program is uploaded successfully and i...
Hai
I'm using nrf52811 and sdk17.1.
I tried all peripheral examples But I can't set advertising data to more than 31 bytes.
If I increase the data size some parameters...
Hi , I am using ZEPHYR rtos , and using the internal bootloader and its working fine and there are two images but now my code size has increased and i can not store 2 images...
Hi
I want to use app_uart_put() to send an array which is over 4096 bytes.I try to change the value of UART_TX_BUF_SIZE to 10K bytes，then call the app_uart_put() to send...
Hey
what are the downsides of using the already burned-in Random Static Device Address compared to a Public Address?
My assumptions are as follows:
Pro
Con...
Hi,
I have been working on Zephyr for the past weeks and have been able to set multiple GPIOs, interrupts and RF functionnalities. But so far, I thought I could handle...
We'd like to use Thingy91 to measure temperature, but it looks like the thermometer (BME680 onboard) gets heat up, when Thingy91 is running for some time.
I placed the device...
Hi,
I'm supporting a customer who is planning to use T-Mobile as their carrier. One of T-Mobile's questions is:
APN requirements: Private APN requires an IPSec VPN or...
Hi,
The spi_config structure zephyr provides is as below: Wherein cs is initialized to the chip select pin. In my project I have a requirement to handle 2 slaves which...
There is a bug in the sample/nrf9160/at_monitor, namely to do with +CEREG unsolicited notification handler called "cereg_mon". "cereg_mon" expects 0-2 +CEREG status code,...
I'm trying to replace a RS232 cable with a BLE bridge with the Nordic Uart Service.
One nRF52832 configured as central (app_uart_example_central) and an other one as peripheral...
Hello,
We are working on a product that contains nRF51822. The product sends continuous data (2 bytes) via NUS service to the mobile app at a frequency of 200ms.
When...
Hello,
I am aware that this is not an Arduino support forum, but if I'm not violating any rules, I'd like to ask a question in hope that someone might have provide a helpful...
I'm developing on an iMac M1.
Over 2 month I tried to get the nRF Connect for desktop (V3.9.3) running on my M1-mac, without success.
Toolchain manager (v0.10.3) works...
