hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hello everybody,
I´m trying to add a custom service to the ble_app_buttonless_dfu example in sdk 17.0.2 . Therfore i increment the NRF_SDH_BLE_VS_UUID_COUNT but this results...
Hello, I´m using nRF52DK BLE module with ContikiNG and I seem to be having issues when trying to connect with the device using the mac address. I´m trying to setup the basic...
Dear all, I'm new on nordic and I have to combine a bootloader BLE+UART. I read some threads but I can't to combine UART + BLE. Can I have an help?
Thanks in advance
Hello,
I am trying to configure my own bootloader for DFU, i use the secure_bootloader_ble_s132 as an exemple for nrf52832 DK.
after i flash the softdevice, the app...
Has anyone done multiple mqtt client connections from an nrf9160? Is it simply a matter of using the mqtt api and defining multiple client structures with unique rx/tx buffers...
Im install nRF Connect SDK 1.5.1 trough nRF Connect 3.6.1 Desktop app to learn zephyr RTOS and switch from nrf5 SDK to it but there is some bug and "Configure nRF Connect...
Hello,
I just receive a PPK2 and looking at power usage/profile. Below is the captured profile when the application is run from the debugger and then detached. This captures...
Hello,
ncs1.5.0
As shown in the question,
I use rtc to generate a 1kHz square wave, and use an oscilloscope to measure only 964 Hz.
Is there a problem with where I...
Hi.
I am using the oberon crypto backend module to use LESC in the application firmware. (I referred to the GLS example)
And I am trying to add a boot loader to use DFU...
Hello all, we are trying to set up a project with a nRF52840 chip in combination with 2 Acconeer A111 sensors. So far I have worked with a nRF52840 development kit and the...
Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello Nordic,
I am using Nordic 52840 (SPI Master) with Intan RHD2216 (SPI Slave) to get data through SPI from the Intan chip.
I have used the Nordic software development...
Dear friends:
I flashed a mesh serial example. I scand mesh beacon by the function "scan_start()". As you can see in below code, I got two uuid device, I want to select...
Dear friends:
I flashed the serial mesh example from Mesh SDK and contact the DK with pyACI according to the guide Using serial interface for provisioning and configuration...
Hi,
I'm looking at using the NRF9160 in a system where every microamp counts. The NRF9160 already includes a DC/DC converter, but as I understand it is step down only...
