Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
We are using I2C bus for communication with a RTC and Accelerometer. But sometimes the I2C get struck in i2c_write. It does not happens always it may happen randomly. We are...
Hi,
I just spent several hours trying to figure out why, using a nRF52 dev kit w/ SDK13 + S132 on both central/client and peripheral/server side, sd_ble_gattc_read() was...
Dear Support,
I have a question about the IPv6 networking with OpenThread. I do have an mesh network with about 50 nodes (PCA10059) and implemented CoAP servers and clients...
I just downloaded SEGGER Embedded Studio (ARM V4.52c) and plugged in my rather old PCA10040. It offered to upgrade the driver, which I accepted. Now, when I click "Connect...
Hi,
Just installed nRF Connect v3.4.1 on a macOS Catalina and get the following error message when starting any of the apps:
I've tried both reinstalling and downgrading...
Hi,
I'm making a peripheral device that needs to minimise battery usage.
My device is essentially a beacon but it allows temporary connections to send a stream of data...
Hello,
I have purchased a new nrf52832 DK board for development. I tried to run some examples like ble_app_blinky which are working properly. But when I tried examples such...
Dear All:
Our team are ready to develop a project with multicentral and multiperipheral
The project topology image lists as follow:
I want to ask how many ram it will...
I know this sounds a crazy question but is it possible to flash a custom nRF52832 board with the same firmware that is shipped with the dev kit and create a mass storage out...
Hello,
I am looking to run the ble_app_uart example from the SDK v17 in nRF only mode on the nRF52840 DK. When running the application as is on nRF only mode, it fails during...
I bought nRF51 dongle from mouser.com. I wanted to put nRF sniffer firmware on it using the guide on the web site. I tried using nRF connect programmer but it can not talk...
Dear all,
I've been struggling with SECUREAPPROTECT register in UICR Flash area on a nRF9160 DK.
I would like to restrict and protect Secure code loaded in Secure mapped...
Hi, we have a custom board using the nrf9160, running modem firmware 1.1, and using the nrf9160_gps driver.
Sometimes we see messages like this:
Tracking: 8 Using: 0...
Hello,
When working with an nrf9160 sample that uses Nordic nRF Cloud and A-GPS, the GPS functions as expected and I am able to get regular fixes. However, when using the...
I have used an nRF 51 dongle for capturing BLE packets on my Mac using Wireshark,, but it no longer works. The only system change that I can recall that might affect this...
